%!$ Easy Diy Woodworking Bench Plans For You #!@

ikea-kitchen-door-hinges I remember seeing your island somewhere but I can't locate a reveal thread. New other see details. Was able to successfully ikea kitchen door hinges a dozen or so doors, taking the adjustment out of the middle and keeping the factory machined hinge holes. I look forward in hearing from you. The center of these holes are located 8. If there's some reason you want to see it sooner though, just let me know and I can ikea kitchen door hinges you some pictures. Hi, Great post!

Handy hint from a professional furniture maker? Do they keep the design consistent regardless of standard or metric? Do you think I will have problems? The door thickness should not be an issue as the doors sits on the outside of the cabinet. There is a small issue of durability if the door is heavier than a standard one. It might need more frequent adjustment to counter sagging or it might even fail earlier than expected.

Good luck with your project! Thanks for sharing the measurements and photos — was a great help as I was fitting IKEA Bodbyn doors to a custom cabinet, and all worked out perfectly!

Thank you for putting all these measurements together so succinctly. Saved me another trip to Ikea! If so, how deep do you drill the 32 mm hole for Buy Kitchen Cabinet Door Hinges Ltd the hinge? Hiya, Took a look at the hinges today and it does look like they go into the door a shade under 12mm or almost half an inch. Let me know if you need more. Ian is it 48 mm from the top and bottom of the door or the cabinet just want to make sure Thanks.

It was on the few cabinets I measured David. Good luck! I answered in a hurry and now I wonder if I misunderstood! Were you asking if the hinge position is 48mm down from the door or the cabinet? The door is always 3 mm shorter than the cabinet.

Almost correct Khaled! But I measured 48mm on the cabinet so I think the 1. Hey thanks a ton for posting this. Was fitting an Ikea cabinet door to a standard Home Depot cabinet and had to drill holes for the small hinge brackets that go on the inside of the cabinet. The measurements worked out great. One difference was it had to be 62mm from the top and bottom of the cabinet instead of 48 for this particular door. Was able to do it in one try.

No worries Tony, glad it helped! Fitting some Ikea shelves to old cabinets. I measured but was worried — this was super helpful, especially as it matches my measurements exactly! I needed to replace the door because of exterior damage, and foolishly tossed it Kitchen Door Hinges 500 to the curb before I measured where to drill the holes on the new door for the hinges.

Can you help? Hi Marco, there are no templates as the holes are drilled by machine in the factory obviously. Then you should be able to use the measurements in the post above to get the exact place for the hole. You can be a fraction out and still be okay as there is of course some adjustment in the hinge itself. Sorry there is Buy Kitchen Cabinet Door Hinges Spring no silver bullet! Be very careful with the depth of the hinge hole, there is not too much spare material!

Usually the top of the forstner drill bit is flush with the material when deep enough. Drill gently and keep stopping and trial fitting the hinge… Good luck! Thanks for providing such clear and well measured drilling specs for the IKEA concealed cabinet hinge. I have been helping a daughter in a kitchen remodel. My skills are limited to describe them generously and had to cut down some Shaker style cabinet doors due to a surprise once the contractor dug into the structure to be modified.

Was able to successfully modify a dozen or so doors, taking the adjustment out of the middle and keeping the factory machined hinge holes. Three Kitchen Cabinet Door Soft Close Hinges Quest doors had to be replaced but came without the hinge holes. I bought the Kreg jig described by one of your readers but could not for the life of me figure out how to adapt it to our situation.

Your template lifted the fog. The Red Sea parted. The Promised Land is in sight. Thank you so much, Ian…. Thanks John, Nice of you to take the time out to respond, makes writing this stuff up all worthwhile. Great you took on a clearly complicated job, despite your opinion of your skills! Just shows that anyone can produce a great result with a bit of thought and a little research.

What size of drill bit is needed for the 2 screw holes needed to fix the mounting plate to the carcass? Hiya, The holes in the cabinet are usually 5mm diameter but this is only good for the little fat grub screws that IKEA use.

Hope that helps, let me know how you get on. Great thanks for sharing you made my day. Bought these new hinges today to be able to install draws in a non IKEA kitchen but forgot to measure.

Regards Robin from Sweden. Hello there, do you happen to know where I can get a hole template for the maximera drawer fronts? My husband built the fronts for the cabinets and drawers for my office.

Our other option is to buy one front and use that as a guide. We purchased the below drawer box. Thanks, Ian! I look forward in hearing from you.

We still have 2 coats of paint to do before drilling. Was tricky to get accurate photos! I think your first plan is the safest. Buy a spare drawer front and then drill the holes right through and use it as a template. Otherwise, here is what I got! Good luck!! If you want an easy way to drill the holes on the door itself, Kreg makes a jig that makes drilling them extremely easy.

Thanks for the writeup, Ian. Yes, I did too, so I figured it must be up to me to write it up lol! Glad it helped. Thanks for the thanks! Hi, Great post! Do you know how far from the top and the bottom of the door are the hinge cups drilled? Darn Roman! I was more thinking folks would be fitting the hinges to their own cabinets!

Instead, focus on the screws marked in the illustration. You can decide if you want it closer or further away from the top panel. By loosening it completely, you can take the hinge apart, allowing you to attach one part of the hinge to the frame, and one part of to the door before connecting the two. Once you've put the hinge together again, you can decide how far out your door should be from the frame. Adjust this one with a very gentle touch. You tighten this screw by turning it to the left, which may feel counterintuitive.

By turning it to the screw to the left, the right side of the door will move upwards. You might also like: How to assemble the Besta cabinets. Close menu. Customize IKEA furniture.

Round Dowel Fence Rail Tool Porter Cable Dovetail Jig 4212 Key Grizzly Dust Collector Parts Unity