%!$ Easy Diy Woodworking Bench Plans For You #!@

tra001-uk-group Most likely the screws themselves are too long and bottoming out. Rated 5 out of 5 by balding gorilla from I love it, solid, powerful, doesnt break. Also, did you remove tra001 uk group plunge spring like Triton recommends before mounting it to a router plate? Auction 3 Fixed price This is almost tra0001 new. Although Festool strives for accuracy in the website material, tra001 uk group website may contain inaccuracies.

The second shows the two touching but won't go any farther. Any Triton experience out there? I am not a super user for routers to begin with and this Triton is a little weird in operations.

But when it works, its brilliant. Triton plunger before. Triton plunger after. Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies.

Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material.

Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice. MikeGE Posts: I sold my TRA last week, so I don't have it in front of me.

However, you have to slide the cover over the power switch out of the way and turn the power off before you can raise the motor and lock the shaft. It's a health and safety feature to make the router more cumbersome to use while inverted in a router table. There is a way to disable this feature, but I never did it because I never got around to using the TRA in the table. Also, did you remove the plunge spring like Triton recommends before mounting it to a router plate? This makes the height adjustments much easier, and you can reinstall the spring if you want to use the router as an external plunge router.

The spring was removed initially. I do wonder about your power switch suggestion. Again, I have used fine before now so I have to wonder if I did something out of sequence, that I think you might be suggesting?

I believe I know the cause of your problem. I had a Triton plunge router in a Rockler router table I sold a few years ago.

I was having problems before I sold it raising the router up high enough for the spindle lock to engage. I felt a lot of resistance when raising it. I checked that the power switch was off and that the plastic cover over the power switch closed and it did.

No visible saw dust or wood was blocking anything. So I took the router off the table and noticed a black plastic cover on one of the metal posts that allow the router to plunge up and down. So I took that plastic cover off I believe it is held down by a screw and noticed it was absolutely packed with saw dust and would not allow the router to raise all the way.

I cleared the sawdust out and everything worked perfectly. It allowed me to sell it and not feel guilty as well. Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website.

Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.

Most likely the screws themselves are too long and bottoming out. Cut the screws down just a little more than the play you have now. Die grinder will get the job done. MikeGE Posts: Carpenter Wood Products Philippines Group I have the TRA mounted in an Incra router plate. I had to remove the thin black plastic base on the router make it fit with the. When I had the router mounted in the Triton router insert, I left the base attached. Does the Woodpecker plate require you to remove the plastic ring? If so, you might try putting the ring back on the router base before attaching it to the router plate.

Wood Workshop Vancouver Group Woodworking Business Card Ideas For