Is Watco Tung Oil 100 Pure,Rockler Floating Shelf Mount,Spiral Router Bit Set Zoo - And More
I have a quart of Tung Oil and after reading enough stuff on-line my eyes are burning and my brain is fried. So what is the skinny on the difference between the two?
Anyone care to educate this dumbass? I think I lost it when one thread went into the properties and polymers of the mix. I've used both, but prefer tung. There's plenty of room for reasonable folks to differ, though. Guideboatguy uses a linseed oil mixture and it looks nice also. I got a Bell years ago and they recommended Watco, so that's what I've used on that boat. I think the Watco penetrates better. It takes longer before you can recoat with Watco and if you rush it, it takes quite a while before it looses its slight tackiness.
I've never gotten enough coats on it to really fill the grain. I've thinned tung oil for the first few coats and used it straight from the bottle since. Eventually it will fill the grain of the wood and gives a nice satin patina, almost like a varnish.
It darkens a bit with age. I haven't found tung to be particularly labor oiil. I usually wipe it on with a cotton rag and wipe off the excess within a half hour. If I do that in the morning, I can do it again at dusk and, unlike is watco tung oil 100 pure Watco, it will have no tackiness and be ready to paddle the next morning.
If the boat slips a bit on the roof rack and you have acrylic carpet tyng padding on the rack, it will rub off the top layers in miles or so, but it is still waterproof. Every five or six coats I lightly sand it with using a block and oil again. Been doing that on my 17 year old Blackhawks all along and they look really nice to my eye. Do make sure to clean up any drips on the hull right away.
Tung is pretty tough stuff once it dries and if you don't get it up right away its a real bear to remove drip marks. Hope this helps PS: I think it takes at least six coats of either to is watco tung oil 100 pure raw wood water-resistant. I'm working on a new sliding seat now and in the course of that little project have been talking with some folks from WCHA. Perhaps that will mean wayco coats to initial waterproofing and grain fill.
We'll see. Live and learn. Watc use tung on all our wood gunnels and like it. We do them once a year or every other year. It creates a nice flat luster finish and seems to repel water nicely. Sometimes it will take up to three coats, with buffing between coats. Jack L. It's worth using for that reason alone. If it's the "pure" variety, though, you should thin it with turpentine or mineral spirits. Otherwise, it takes forever to dry. Most tung oil finishes you'll find are already modified with solvents and metallic driers is watco tung oil 100 pure just like Watco and other oil finishes.
In the end, it won't make a whole lot of difference which oil finish you use since they're all basically variations on the same age-old formula, each with its own unique sales pitch.
They all form a very thin barrier that needs regular maintenance. Watco I use Watco Is watco tung oil 100 pure oil quite often. Can be found at Home Depot last time I checked. Having a real hard time finding wtco tong oil anyway. Is watco tung oil 100 pure applied a few light coats, but once I got kil boat back in the water, the gunwales felt slimey.
Maybe I needed to buff it more. Many lite coats work much better. I now use a green scrubby to apply it as is watco tung oil 100 pure suggested. This smothes and applies in one coat. You need to apply it several times wafco year and yes new wood needs a lot at first. I love the smell which adds pleasure to the job. Just wiping it on does nothing. Seems that varnish and paint formulations are changing with new VOC laws in some states.
In Maine we can no longer buy oil based paint. And the new formulations will not penetrate the older oil based stains…which for exterior stains leave a layer of paraffin for protection puree the surface. My husband has been scrubbing rough sawn cedar for a year to restain the house. Watco is Dapper Dan for your gunnelsand I like like odor of my wood treatment; the pleasing smell is half the point.
Pure tung oil cures fairly quickly… …as in 24 hours at room temp. With ANY pure oil finish and with most varnishes, if you try to rush it and re-apply before the first coat is cured, it will dramatically extend the cure time. The more coats you add, the worse the problem gets. This is easy to test: Finish a piece wacto wood, then take a plane set for a very fine shaving.
Tung oil vs. Behlen pure is watco tung oil 100 pure oil. Fung printed on the label is to thin 4 parts solvent to 1 part oil. Old stock? I expect this accounts for the different experiences people have with cure times for tung oil. The varnish mixtures cure in hours. Pure oil takes days.
Are you using my gunwale treatment? Because I too am a Watco-man…Frequent light coats of Watco Teak Oil; remember this one simple precept and your time will not have been ill-spent. Minwax Tung Oil Finish is what I ended up with. I guess the thing to do is just try it on a left over piece and see how it goes. Thanks for all the answers!
Differences Between Tung Oil and Watco? Possum tastes better fried in tung oil than in Watco, at least to me. A geographical oddity … … two weeks from everywhere.
|
Wood Planks Texture 40 Gunstock Carving Vise Quote Sign Into Router Settings 95 Drying Out Wood For Turning |
Sensiz_Olmuyor
25.12.2020 at 23:46:42
nellyclub
25.12.2020 at 22:29:51
nice_boy
25.12.2020 at 23:23:38