Cheap Cyclone Dust Collector Kit,Sawdust Collection For Miter Saw 93,Do It Yourself Garden Art Vessel,Waterlox Finish Sealer Ltd - For Begninners
That said, I've seen it on sale, and it has made my 12 gallon shop-vac feel adequate again. For that, I am eternally thankful. I have waited to do a review until I had used the dust collector for a few months. I have been very impressed with the cyclone. I use it on my miter saw, bandsaw, and orbital sander. It have noticed a drastic reduction in fine sawdust. I did not attach the bucket to my shop vacuum, but will either connect it to my vacuum or build a cart that will hold both and make it easier to empty the bucket.
I have seen video's on You Tube that were a prank but this is not one of then. I purchased my Dust Deputy from Woodcraft for easy return if it did not work. I still have it and won't give it up. I create a lot of saw dust, wood shavings and sanding dust. You still need to clean the filter ocasionally from the fine dust.
I still can't believe it. Incredible to see the a clean Vacuum and all the derbies properly directed to the secondary container By the action of a vortex of the Dust Deputy Your Shopsmith or any other Vacuum will never loose suction power…because it will never get any Shavings, dirt and other materials used in your shop If you are looking for a complete setup for our shop the Oneida Dust Deputy in combination Rikon Dust Extractor And the Woodriver remote control will turn your shop into a clean room dust free working environment.
We bought one Oneida dust deputy kit for my wood carving studio but my husband loves it so much he won't let go of it. I now must purchase another for me. This thing is awesome. It separates out almost everything dust-wise that I can suck up with my shop-vac. I've used it daily for the past month, and only had to clean my filter one time, just for good measure. It wasn't even that dirty, just felt like I needed to do it.
It can really hog up the dust too, My band-saw doesn't have a proper dust collection attachment, but only has a large box shoe box size at the bottom for the dust to pool, so there's a large quantity of dust in there most of the time, all it takes is a few seconds with the shop vac to have it spotless.
The only thing that can make it into the vacuum is the occasional long strip from a hand plane or piece of paper towel. Sure, you can buy the cyclone by itself, but then you gotta do the run-around to find a sealing material, hardware to attach it to your vac, casters, buckets, OR, you buy the kit and be done with it, using it in about 20 minutes.
In the same vein, you could build one, BUT, again, this thing is a performer, and unless you're just into aerodynamics and tuning of cyclones, you'll never match the ability of this thing.
I use this to vacuum up wood chips and saw dust. It really saves on shop vac filters. I did not attach it to the shop vac because it made the assembly to cumbersome to pull around the shop. So, I keep the units separate. In this mode it tipped over easily. So I mounted the bottom bucket to a 12"x12" piece of plywood and mounted four casters on the plywood.
Great addition to the shop. This thing works fantastically! Aside from my table saw, it's probably the best purchase I've made for my wood shop. Only a very small amount of dust and one Styrofoam peanut have made it past this thing. Also, the lid for the buckets that come with the kit are very flimsy; but that has nothing to do with the Dust Deputy itself.
The suction is the same. I still have dust flying around in my shop when I use my table saw. I am setting up a small woodworking shop and couldn't justify a large dust collection system. This unit when hooked up to a shop vac works great. It filters even the fine dust from sawing and routing and there is barely a trace that makes it to the shop vac. I even hooked the output hose from my DeWalt planer to this unit and left the exhaust on the top of the Dust Deputy open to avoid back pressure from the shop vac.
The Dust Deputy collected all of the chips with no problem. I do have a complaint about the cyclone mounting on the bucket lid. The lid is so flimsy that the cyclone tilts when hoses are connected and it is only a matter of time before the lid or flange fatigues and something breaks. I made a ring out of plywood and put it on the underside of the lid, bolting the cyclone thru the lid and thru the ring with longer screws which reinforced the lid.
See attached photo. There are some videos on Youtube showing other supports people have made and I highly recommend something be added. I'm amazed Oneida has such a good collector design with such a flimsy mounting scheme.
I use the Dust Deputy attached to my table saw, planer and router table, and use it while vacuuming up the shop floor. My new shop vac still has a clean filter and nothing to dump out of the tub. No mess. Have breathing problems but hardly notice dust, shavings, etc.
I use the Dust Deputy as a fixed cyclone by my lathe. It saves me having to take my ShopVac apart to dump the sawdust and wood shavings. As well as having to clean the filter. Since I don't move the Dust Deputy around I didn't need to use the included hardware kit: attach casters to the 2nd bucket; then bolt the 2nd bucket to the vac. If I was going to attach the Dust Deputy to my Shop Vac then I would probably just rest the bucket on the accessory carrier and use a nylon rachet strap to hold them together.
Does a wonderful job of collecting sawdust from all tools I've used. Table saw. Router table. Drill press. Planer and jointer. I have in hooked to a Fein Turbo I and have been very pleased. Virtually no dust inside. Good efficient dust collector. I am a little concerned about the strenght of the lid and its attactment to the cyclone.
First Reveiw: It works as advertise, picks up the fine dust before it can move it my vac. Easy general clean up around wood lathe without pluging up or overloading shop vac. Removes a lot of chips and dust before they hit the shop vac filter.
Works Great! My only con is that because it is lightweight it tips over easily. I fixed this by putting two bricks in the bottom. Very good job at dust collection for single use tools. I watched a few videos about it and had to get one to try out. Yes it works super! After setting it up I had to try it out so I dumped the whole Shopvac inners on the floor and cleaned out the filter.
Oh my goodness, next to nothing in the shopvac after sucking everything up. Keeps the shop vac filter cleaner Works great on any shop tool with a vac hose hook-up It is a mini shop dust collection system in it's-self. I do not have a fixed vacuum dust collecting system and must move unit from equipment to equipment in a small shop.
I did not want to drill holes in the bottom of the bucket for the casters so I'll need to build a caster base, no problem there. Overall, this is a great buy for the price and is extremely efficient for keeping dust from clogging the vacuum filter.
The seperator seperates good but the bucket is too small and the hoses don't stay on the seperator very good even with hose clamps. Connected to a small Rigid shop vacuum, the bucket on the Dust Deputy collects virtually all the sawdust and chips, so the filter remains clean and the suction is amazing. Wish I had installed this years ago. There are many ways to mount and attach the unit to your vacuum, and this may take some planning to end up with a convenient system, but Oneida includes casters, hardware, a second bucket and suggestions.
And the suggestions are written and pictured so as not to insult the handy folk who will use this tool. I don't have to keep stopping to clean the shopvac filter when using the Dust Deputy.
Excellent in maintaining suction of my shop vac. Keeps my filter clean. Shop vac remains remarkably clean after 15 hours of use! The unit could use a less flexible lid as right now the cyclone tower can lean easily - degrees - because of flex in lid to which cyclone is attached. Best about my order was very prompt delivery using standard shipping! This one really works. I've had other separators, that collected chips, but not dust - this one does.
After I hooked it up, I sucked up all the dust on my shop floor. The 5-gal bucked was full, but almost none in my Shop-Vac, including the filter. I noticed no reduction of suction. It was gratifying hauling out a bucket of dust rather than my entire shop-vac. The only minor knock I have is the lid is very flimsy.
Once the seperator is installed with the hose attached, it flexes quite a bit. You could also use a different lid. Overall, not a big deal considering the overall good performance.
It has been a good purchase, it works well as promised, it's very efficient for small duties. A little bit expensive the shipping to Italy! Great product! While sanding paint off doors, very fine dust, I use to unblock the paper filter of my shopvac every couple of hours, now I can work all day and only empty the plastic bucket. The deluxe kit was easy to assemble and the DD works great.
I am a beginner wood worker and don't know how I got along without it. I use the DD in combination with the Craftsman smart plug and they are a great combination. This works great with machines that produce a lot of sawdust. I use it with a special shop vac designed for drywall contractors because my woodturning produces a lot of very fine sawdust.
The vac uses paper bags and a hepa filter. The bags filled fast before using the Dust Deputy. Now it will be years before I need to change bags. I bought this for use cleaning up the small, oily metal clippings generated by my mill. The idea was to use my wood working dust collector for vacuum, but to catch the swarf before it could reach the collector. It worked moderately well, but there are some design issues.
The port size is a little odd; 2" hose won't clamp directly over either the inlet or outlet. The plastic lid for the bucket is a little flimsy; the cyclone separator rocks around on it. The whole assembly is so light weight that moving the vacuum hoses causes it to tip over. Included in the kit are casters for making a rolling base not shown in the Woodcraft picture.
I use the oneida hooked up to my shop vac for dust collection off my power tools. This model comes with 2 buckets so one acts as a holster for the other allowing you to attach it however you like to your vac or a homemade cart.
If your looking to make a cart for it Shopnotes magazine issue 97 has a great plan for one. Great product from Oneida you wont regret buying this one. This thing is great, I've emptied the full bucket 4 times and not 1 speck of sawdust or anything for that matter has made it into my shop vac!
It all stays in the bucket! As a kit it tries to be complete unfortunately the suppled hose does not work well with my Rigid Vac. I know "There's nothing that can't be solved with duct tape," but it's a kluge. Also You really need to build a cart as it's cumbersome to drag around.
It does work as advertized. I'll work on it and write another reveiw when I've got the hose adapted and a cart built. I saw a couple videos of this item on YouTube and it convinced me to purchase it.
I have to say it does everything they claim it does. I was tired ov having to clean out my shopvac filter each time the tub was full, the cyclone solves that problem. I will say that it is suseptible to clogging. But it is very easy to un-clog, you just have to be aware of this and watch out for it. This whole system makes clean up a breeze.
I got this system because I was tired of cleaning clogged saw dust and particles from my shop vac filter every time I had to empty the 5 gallon bucket. It does everything it claims. I have noticed, however, that hand plane shavings will clog the port to the cyclone tube and I suspect that the shavings that get through interfere with all the dust reaching the bucket because I do find a considerable amount of saw dust in my shop vac when I've been vacuuming up hand plane shavings.
I was tired of having to clean out the filter of my shop vac every time the tub got full. The Dust Deputy has done everything it claims. I have noted however, that when I vacuum up shavings from my hand plane that it will tend to clog where the vac hose enters the intake port of the dust deputy and when you introduce hand plane shavings it decreases it's efficiency in separating the fine dust from my shop vac.
There must be something about hand plane shavings that interupt the flow of the fine dust down in to the collection bucket.
But either way, I'm not having to clean out my shop vac no where near as frequently and no more cleaning out the filter. Pro: I dump sawdust on the floor just to see the cyclone in action. The dust collector collects So, the filer is dealing with only 0.
AS cyclone, elbow adapters, SD hose, five-gallon buckets, a gasket, caster wheels, and hardware is included in the package of this dust collector. You can definitely opt for it if you are looking for something versatile and long-lasting. This sleek-looking cyclone kit is a must-have for an enthusiast. The kit is compatible with most dust collectors and comes in a simple and effective design that is easy to use.
Like the dust collectors mentioned before, this one is also manufactured by the Oneida Air Systems. This cyclone dust collector kit is suitable for small shops and homes.
The product prevents filter clogging, which is a huge advantage for users. The lifespan of the dust collector is also increased by this cyclone kit. It is highly efficient when it comes to collecting dust and debris.
The machine comes with an air ramp which is integrated into its system. The kit is also Jet 14 Bandsaw Dust Collection compact and very lightweight, so working with it completely hassle-free. You can definitely go for this cyclone kit if you are looking for something long-lasting and convenient.
This versatile cyclone dust collector is compatible with most vacuums. It can pick up both wet and dry materials, including the difficult ones like hair. You can also pick up dust, concrete particles, wood chips, debris, and more with this dust collector. The machine is suitable for both home and industrial use. The dust collector comes with a well-built inch hose.
You can attach the hose directly to the outlet and inlet of the dust collector. If you are professional, you will love the design of this product. It has been engineered keeping woodworking, CNC machining, textile industries, and construction work in mind. The machine is perfect for heavy-duty dust extraction.
The collector is also well built and can withstand high temperatures. With its great quality flexible and puncture-resistant PU hose, this dust collector is excellent for work purposes. We recommend it for use in industrial work. For most cyclone dust collectors, two-stage units for separation are always preferred over the single-stage units. The reason behind this preference is that the two-stage units ensure higher cubic feet per minute of airflow.
This cyclone dust collector comes with the two-stage units, so it is more efficient compared to other dust collectors. Constant suction is ensured in this machine by preventing heavy debris from reaching the filter. This debris is sucked into the collection drum. The filters are directly mounted in this dust collector, which prevents ridge and flex in the hose. However, fine the particle is, this dust collector will collect it and clean your area thoroughly.
The dust collector is designed to pick up particles that are even smaller than 1 micron. A pleated material is used for filtering out these tiny dust particles. A drum of gallon size is used for collecting the heavy debris. The debris is captured with levers that have quick-release features and are emptied with casters. The Swivel Casters make this dust collector portable and easy to move around with.
If you are looking for something quick and easy to use, this cyclone dust collector is perfect for you. Are you a craftsman who works with a lot of dust and debris every day? Well, this outstandingly designed cyclone dust collector is the best solution for you. The machine has a modern and fashionable design that will fit right into your workstation. You can use it for both home and industrial spaces. It comes equipped to handle a large amount of dust and debris.
Design of this cyclone dust collector is compact yet sturdy. It has all the necessary features a craftsman would need. With its very high suction force, it can work quickly and reduce the pressure on the filter. If you are a professional craftsman who needs a portable dust collector, you should definitely go for this one. Time to make it super easy to clean space by quick dust extraction and separation.
These DIY dust collector plans will provide step-by-step instructions, diagrams, and even video tutorials to build one stage or two-stage cyclone dust collection like a pro. Get the best out of your plastic buckets by making a dust collector, use 1 or 2 buckets to build a dust collector, will just work fine. You will get a whole bag of tricks too about how to upgrade a dust collector so it will work fine for the current situations.
These DIY cyclone dust collector projects will provide all the tips to build a lovely one in no time. Make it super quick and easy to clean your home with this wall mount dust collector. Next, you need custom filters, expandable dust hose, and miter saw dust collector, etc.
Get here free plans to build a custom DIY cyclone dust collector, will surely impress with its super functional behavior. Make the dust collector using plywood, a trash can, and custom pipe fittings.
Next, add it up with a normal shop vacuum to make this see-through cyclone dust collector. Get here a free plan to build a quick DIY cyclone dust collector system, will give a big helping hand in home cleaning.
Build this cyclone dust collector using a shop vacs, and this will not let the filters clogged but will keep them running smoothly. Time to save a lot of home cleaning time using this system. If you are having dust allergy, then time to keep your lungs safe from the airborne dust using this cyclone chip separator will help keep your home clean and tidy.
This system uses a 2HP model from the Harbor Freight and uses the plastic drums as trash cans. Details here instructables. Save a lot of home or shop cleaning time with this dust extraction, made for home workshops. It is super quick to compose, and the whole system will cost you much less. Grab the rigid 4-gallon shop vac and a mini DIY cyclone dust collector to build this dust extraction system. Details here woodworkingfor.
|
Lathe Tools Without Handles Service Miter Gauge Shooting Board 00 |
Leonardo007
21.07.2020 at 10:42:47
BOY_FIESTA
21.07.2020 at 21:16:53