Open Hardware Laser Printer Model,Wood Boat Plans Pdf Windows,Small Box Latch Hardware Controller - Reviews
This page requires Javascript. Modify your browser's settings to allow Javascript to execute. See your browser's documentation for specific instructions. HP Customer Support.
Select your model. How does HP install software and gather data? This document explains how to set up the physical parts of the printer. Complete these steps before installing the printer software on the computer. If the printer hardware is already set up, see the Links to software installation instructions section at the end of this document for help with software installation. Step one: Unpack the printer Select a site to place the printer that meets the following specifications:.
A sturdy work surface, well-ventilated area, and away from direct sunlight. HP recommends that four people move the printer. Figure : Space requirements. Remove the HP printer from the box, and then verify that the contents match the illustration below.
Figure : Contents of the box. Figure : Remove the packing tape. Figure : Remove the packing material under the scanner lid. Step two: Insert the staple cartridge carriage in the inner finisher Open the front door on the inner finisher. Figure : Open the front door on the finisher. Figure : Remove the shipping lock. Push the green lever callout 1 to disengage the finisher, and then pull the finisher away from the printer callout 2.
Figure : Disengage the finisher and pull it away from the printer. Insert the staple cartridge carriage into the stapler by pressing the colored-handle inward callout 1 until it snaps into place callout 2. Figure : Insert the staple cartridge carriage into the stapler on the finisher. Step three: Attach the output tray to the finisher note: Make sure the finisher is still pulled away from the printer.
Attach the output tray by aligning the tabs on the front of the tray with the openings on the finisher as shown below. Figure : Attach the output tray to the finisher.
Figure : Insert the tabs into the openings and push down. Figure : Push down on the tray until it snaps into place. Step four: Attach the wire paper guide and reattach the finisher to the printer note: Make sure the finisher is still pulled away from the printer.
Hold the wire paper guide with the ends facing to the right and then insert the ends into the openings on the finisher. Push the ends to the right to secure the wire paper guide on the finisher.
Figure : Attach the wire paper guide to the finisher. Figure : Lower the wire paper guide. Figure : Reattach the finisher to the printer. Step five: Insert the cartridges Open the front door on the printer.
Figure : Open front door. Remove the toner cartridge from its packaging by removing the end caps callout 1 , removing the cartridge from the plastic bag callout 2 , and then removing the orange protective shield callout 3. Fingerprints on the developer roller can cause print-quality problems.
Figure : Remove the toner cartridge from its packaging. Support the toner cartridge with one hand underneath it, while holding the cartridge handle with the other hand. Align the toner cartridge with its slot on the shelf, and then insert the toner cartridge into the printer. Fingerprints on the developer roller can cause print defects. Compute4Less Corp.
BTE Outlet. Aztek Computers. JSAO Electronics. Ebiz Office. PQ Electronics. Technology Galaxy. In Stock. Up to 10 ppm. Up to 12 ppm. Up to 14 ppm. Up to 15 ppm. Up to 16 ppm. Up to 17 ppm. Up to 18 ppm. Up to 19 ppm. Up to 20 ppm. Up to 21 ppm. Up to 22 ppm. Up to 23 ppm. Up to 24 ppm. Up to 25 ppm. Up to 26 ppm. Up to 27 ppm.
Up to 28 ppm. Up to 29 ppm. Up to 30 ppm. Up to 31 ppm. Up to 32 ppm. Up to 33 ppm. Up to 34 ppm. Up to 35 ppm. Up to 36 ppm. Up to 37 ppm. Up to Open Hardware Laser Printer Manual 38 ppm. Up to 40 ppm. Up to 42 ppm. Up to 45 ppm. Up to 47 ppm.
Up to 50 ppm. Up to 46 ppm. Up to 49 ppm. Up to 48 ppm. Up to 43 ppm. Up to 8 ppm. Up to 52 ppm. Up to 55 ppm. Up to 62 ppm. Up to 63 ppm. Up to 65 ppm. Up to 70 ppm. Up to 58 ppm. Up to 60 ppm. Up to 1, pages monthly. Up to 2, pages monthly. How does HP install software and gather data? Connect the network cable optional. Connect the power cable and turn on the printer.
Load Tray 2, Tray 3, and Tray 4. Load the 1,sheet high-capacity input tray Tray 5. Verify that the printer functions. Update the firmware optional but recommended. Install the printer software. This document explains how to set up the physical parts of the printer. Complete these steps before installing the printer software on the computer. This document includes the following steps to set up the printer:. Unpack the printer Select a site to place the printer that meets the following specifications:.
A sturdy work surface, well-ventilated area, and away from direct sunlight. Allow enough space around the printer to open all doors and trays. Follow the instructions on the box to install the ramps and roll the HP printer out of the box, and then remove the packaging material.
Verify that the contents match this illustration. HP recommends that four people move the printer. Remove all tape and packing material from outside the printer. Open all doors and paper trays, and remove all tape, orange plastic tray inserts, and other packing material from inside the printer. Figure : Remove the shipping tape and foam protector. Connect the network cable optional If the printer is to be connected to a network, connect the network cable now.
If not, skip this step and go to the Connect the power cable and turn on the printer section in this document. To use a USB cable to connect the printer to the computer, connect it when prompted during software installation. Figure : Connect the network cable. Connect the power cable and turn on the printer Figure : Connect the power and turn on the printer.
Connect the power cable to the printer. To prevent damage to the printer, use only the power cable that is provided with the printer. The voltage rating is on the printer label.
Wait for 60 seconds before continuing. During this time, if the printer is connected to a network, the network recognizes the printer and assigns an IP address or host name for the printer.
When the Home screen appears, touch Initial Setup , and enable basic printer functions. For advanced setup for network-connected printers, enter the printer IP address in the address bar of a Web browser after software installation is complete.
To find the IP address, follow these steps:. Refer to the table in step 5 to determine your control-panel type. FutureSmart 3 : From the Home screen on the printer control panel, touch the Network button. FutureSmart 4 : From the Home screen on the printer control panel, touch the Information icon, and then touch the Network button.
Close Drawer React Navigation Key Workbee Cnc Router Machine Java Wood Hole Jig 100 |
BESO
07.01.2021 at 15:54:26
2oo8
07.01.2021 at 21:23:15