%!$ Easy Diy Woodworking Bench Plans For You #!@

new-craftsman-radial-arm-saw-on Are Radial Arm Saws a Thing of the Past?

Printed in U. WEAR Learn specific its applipotential with three-prong plug, it should srm plugged into a three-hole grounded receptacle. If adapter is crzftsman to accommodate two-prong receptacle, the adapter wire must be attached to a known ground. Never remove third prong. The hazards. That recommended cause if the tool contacted. That 5. Always wear safety glasses or eye shields before commencing power tool operation.

We recommend Wide Vision Safety Mask for use over spectacles, or standard safety glasses. A guard or new craftsman radial arm saw on part that is damaged should be properly repaired or replaced. TOOLS Don't AVOID accidents. Consult be kept crafstman dusty. DON'T footing Keep tools sharp and clean performance. Follow instructions changing accessories. CLEAN areas and benche. Craaftsman safer than using your hand, frees both hands to operate tool.

AVOID to get caught in new craftsman radial arm saw on is recommended for best Rubber-soled footing. Electrical Connections Operating Controls Basic Saw Operations Motor Trouble Shooting Chart Guarantee Repair Parts Basic Saw assembly Rear cgaftsman Table spacer Rip fence Front table Elevation crank assembly Knob assembly, pull Switch key Arbor wrench Craftsmaan, medium, ".

Nut, hex. Machine screw, pan-hd. Setscrew, eup-pt Machine fraftsman, pan-hal. Mounting Your and preassembly Saw on a Workbench Mount on a Craftsman Power bench, in such a position that free to rotate, 4. Tool Base or a sturdy, flat the elevation crank will be 3. Installing Knob the Figure you Elevation are working on the saw.

Crank Swivel and tighten Latch-Pin eaw preventing tracks. Figure on the carefully start and slide the carriage onto the radial-arm tracks. The assembly must be held parallel new craftsman radial arm saw on the arm so that all four of the assembly bearings will smoothly slide onto the new craftsman radial arm saw on arm tracks, thus 2 a.

Install the elevation crank and on the flat portion of the shaft. Assembly a. Rotate tbe elevation crank clockwise several turns and remove the shipping block from between the carriage and ram radial arrn. Craftsamn the carriage stop screw. Iockwasher and warning tag. This cord must remain unplugged whenever Installing the Motor and Carriage Radial Arm Figures 2 and 3 strain on the bearings and stop screw and Iockwasher.

Unless this is done carriage can rol! Remove the two shipping screws from bottom of motor, and discard. Leaving these in would limit craftsmzn of cut.

Check the cord in the arm cord clip to make sure there is 30 inches length of cord between this clip and the cord clip on the yoke. Remove the carriage new craftsman radial arm saw on right-hand carriage cover. Tighten the screws lightly -- the indicator will be new craftsman radial arm saw on, later c, Reinstall the carriage knob, 4 then new New Craftsman Radial Arm Saw Guide craftsman radial arm saw on the cover and knob.

Similarly attach the remaining rip-scale indicator to left-hand carriage cover, then reinstall this cover Note that there is no arn on the left side; only [he cever need be removed and reinstalled.

Loosen the guard-clamp assembly. Place the arbor wrench screw and remove on the shaft wrench on the hex portion the saw blade. The motor shaft has left-hand threads. Figure e. Remove new craftsman radial arm saw on. Place the saw blade, nut, collars, and guard assembty where they will be out of your way during the following adjustment steps. If the table craaftsman the table - are not precisely squared with the saw-blade travel in all operating positions, the blade may not produce clean, uniform cuts.

Removing shaft nut, Figures 4, 5 and 6 Loosen the handle up bevel lock knob and b. Swivel the motor counterclockwise of the shaft is pointing straight lock knob. Loosen them just enough for the ssaw to move up or down when tapped with a rubber mallet. Lay the handle end of the arbor wrench on the mounting support and, while holding the wrench flat on the support, carefully rotate the elevation crank to lower the motor until the motor shaft end just touches the wrench surface.

You should be able to 8 slide the resistance. Do qot change the setting until you have satisfactorily completed the adjustment of both table mounting supports.

Repeat the directly support above the front, attaching screw. Tighten the two through "h" to make certain tha fits between the motor-shaft en channel in an identical manner a front. Adjust the right-hand same manner, without tion setting. It is upside down when the face in which the screw holes are counterbored is at bottom.

Drive the T-nut carftsman with loose parts into the smaller of these two center holes. Turn the xaw table top side up and place it on the table supports, locating it so that ob six screw holes near the board sides are aligned with their corresponding holes in the two supports. In the larger of the two center holes place one 17! Move the carriage to its extreme tighten the carriage lock knob.

Lay the rear table board on pn across the front table to serve as a straightedge. Sight under this straightedge to determine whether the front table board is high or low at its new craftsman radial arm saw on. If the center do not tighten it. In the the T-nut underneathrear position, and set-screw. Install one 1! The board should be snug against the supports, but not held too tightly to be moved by tapping it firmly with a rubber mallet.

Squaring the Crosscut Travel Figures 16 through 23 Figure 19 a. Loosen the carriage lock knob, move the carriage to the approximate center new craftsman radial arm saw on the radial arm, then retighten the lock knob.

Install 1 the saw blade, as follows: Place on the motor shaft, in this order: 1 One of the two blade collars, flat face out; 2 Cgaftsman blade, with when The blade; 2 the teeth pointing in a clockwise direction you are facing saw-blade end of motor; 3 remaining blade collar, flat face against and 4 The shaft nut. Tighten the shaft nut as shown in Figure Do not bump or iar the arm. Tap cgaftsman arm latch solidly with the palm of your hand to seat the arm lock pin firmly.

By turning the elevation crank counterclockwise, lower the blade new craftsman radial arm saw on it just clears the front table. Figure 21 Figure 23 22 Now slowly move the carriage outward along the radial arm. The tooth you have neq should just touch the long leg of the square at all points.

If it does not, make the following adjustments: cgaftsman If your craftsmaj tooth moves into the square as the carriage is moved outward, tap the left-front edge of the table with a rubber mallet until you can perform step "g" correctly. Also refer to page 20, of Trouble Shooting Section.

Tighten the screws. Position the rip fence, spacer board and rear board behind the front table board, as shown. Install the two table them at the rear of securely. This should be tacked in place for easy replacement.

Find many great new & used options and get the best deals for Sears Craftsman 10 Inch Radial Arm Saw With Stand at the best online prices at eBay! Free shipping for many New Craftsman Radial Arm Saw Keyboard products! The new compound miter saws and radial miter saws are much nicer. They are a lot more accurate and are becoming much more reasonably priced. The radial arm saw can be a lot more flexible if you add sanding accessories or chucks for shaping. In terms of safety, they can be a bit more tricky.

Rikon Helical Benchtop Jointer Node Woodworking Marking Out Tools Youtube Portable Wood Sanding Machine Uk