%!$ Easy Diy Woodworking Bench Plans For You #!@

jet-jml-1014-mini-wood-lathe-manual-rating For jet jml-1014 mini Jet Jml 1014 Mini Wood Lathe Review Mag wood lathe manual rating up to 50 feet, use a manial AWG or larger gauge cord. Form the habit of checking to see that keys rting adjusting wrenches are removed from the tool before turning it on. Page 7: Electrical Requirements Electrical Requirements In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. All visitors should be kept safe distance from the work area. Spur Center Also use face or dust masks if the cutting operation is dusty. Shipping address other than a Post Office box.

Previous Page. Next Page. M Ph. If one of our tools needs service or repair, one of our Authorized Service Centers located throughout the United States can give you quick service. Page 4: Warning Warning For your own safety, read this instruction manual before operating the lathe. Wear eye protection. Do not wear gloves, necktie, or loose clothing. Tighten all locks before operating. Rotate the workpiece by hand before applying power.

Rough out the workpiece before installing on the faceplate. Page 5 Do not operate this lathe while tired or under the influence of drugs, alcohol or any medication.

Turn off the tool and disconnect from power before cleaning. Use a brush or compressed air to remove chips or debris — Page 7: Electrical Requirements Electrical Requirements In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This tool is equipped with an electric cord having an equipment-grounding conductor and a grounding plug.

The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and ordinances.

Page 8: Unpacking 1 — 3mm hex wrench 1 — 5mm hex wrench Assembly The JMLI is fully assembled and comes ready to use right out of the box. However, it is a good practice to thoroughly check the machine for loose fasteners, handles, etc.

If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord. Do not wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry which may get caught in moving parts. Nonslip footwear is recommended. Wear protective hair covering to contain long hair.

Also use face or dust masks if the cutting operation is dusty. Everyday eyeglasses only have impact resistant lenses, they are NOT safety glasses. Keep proper footing and balance at all times. Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories. Make sure the switch is in the off position before plugging in the machine. The use of improper accessories may cause a risk of injury.

Serious injury could occur if the tool is tipped or if the cutting tool Jet Mini Lathe 1014 Manual License is unintentionally contacted. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation.

A guard or other part that is damaged should be properly repaired or replaced. Feed work into a blade or cutter against the direction of rotation of the blade or cutter only. Welcome to ManualMachine. We have emailed you a verification link to to complete your registration. Log in Sign up. Forgot password? Enter your email and check your inbox.

To place an order, call Please have the following information ready: 1. Visa, MasterCard, or Discover Card number 2. Expiration date 3. Page 3 For your own safety, read this instruction manual before operating the lathe.

Do not wear gloves, necktie, or loose clothing. Rotate the workpiece by hand before applying power. Rough out the workpiece before installing on the faceplate.

Do not mount a split workpiece or one containing a knot. Also use face or dust masks if the cutting operation is dusty. Everyday eyeglasses only have impact resistant lenses, they are NOT safety glasses. Page 5: Electrical Requirements Electrical Requirements In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock.

This tool is equipped with an electric cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and ordinances. However, it is a good practice to thoroughly check the machine for loose fasteners, handles, etc.

Fine Woodworking Simple Workbench Example 4212 Porter Cable 12 Dovetail Jig Video Wall Woodcraft Pen Turning Blanks Kr Marking Knife From Saw Blade 98