%!$ Easy Diy Woodworking Bench Plans For You #!@

shop-vac-dust-collector-system Then go with these 15 easy to make and cheap DIY dust collector plans that will help you easily clean your workshop and will provide so many different structure modules shop vac dust collector system choose from. My Account. Read on to find out dst. It is super quick to compose, and the whole system will cost you much less. Ships From Woodcraft. Air Filtration Unit.

Often, when you turn on your Shop-Vac, you will notice a cloud of fine dust blowing out through your exhaust. This is because excellent dust will flow through most filter systems that come with shop vacs.

Choose a HEPA filter instead. They will make your shop vacuum dust collector more efficient. This will save you so much time and make your work easier.

You can add up to ft. Video Credit — Alex Quiroz. So can a shop vac be used for dust collection? Well, you have an answer to that. More importantly, you also have everything that you need to know for this process to work. Irrespective of all that, if you want any home cleaning tool to last, you must take proper care of it.

Learn all the top care and maintenance tips for your shop Vac too. This is the simplest tip that every user needs to know. Woodworking Plans Now is a participant of the Amazon Services LLC Associates Program and ClickBank Affiliate Program, an affiliate advertising program which is designed to provide an aid for the websites in earning an advertisement fees by means of advertising and linking to Amazon and ClickBank products.

Skip to content. WWPN Staff. Buy Dust Collector Adapter Many people want a shop vac with a dust port that they can directly Dust Vacuum System Shop Zip Code plug a dust hose into. Install a Better Filter Finally, you should install a better filter. Get Now. Recent Post. Free Woodworking Plans. I also wanted to use my existing shop-vac, knowing from experience that the 5. The last requirement was it had to turn on automatically, I was getting tired of "aw crap", forgot to start shop-vac first! With all the above, the photos pretty much explain where I went from there.

I opted for ball valves instead of blast gates, mainly because it was going to take more work to match fittings for the blast gate. I wrapped duct tape on the PVC pipe end to the size where I could use a hair dryer to expand the vacuum hose and slide the hose over the duct tape. When the hose cooled, it made a perfect fit. I decided early on to use the Dust Deputy cyclone and capture most of the dust and chips before they made it to the shop-vac so that I would not have to clean so often.

The other driving factor was that this allowed me to put the shop-vac above the ceiling. More floor space and less noise. I have half filled the 30 gallon drum with sawdust and have yet to empty the shop-vac or clean the filter. I decided to anchor the PVC pipe going through the ceiling by using a floor flange for electrical conduit and drilling a clearance hole for the PVC, then gluing the PVC in place.

I also used a pipe clamp above the ceiling on the PVC. I, luckily, have all 5 of the machines I use the shop-vac on, on one circuit, which simplified the automation requirements as I just had to monitor one point. I settled on a design that did not limit the current in case I did try to run multiple machines, using an Aprilaire 51 current sensing relay that is normally used for humidifier circuits triggered from the furnace fan motor current. It is only rated for 50 watts so I used it to drive a relay.

When I first prototyped the circuit, the relay was energizing immediately. After a replacement current sensor gave the same result, I started experimenting with loading, and determined that although the specs said 50 watt max, it should have also said 10 watt minimum load. The particular relay I used only draws 10ma and measures 5k ohms resistive load, so I added a 2k ohm 20 watt wirewound resistor in parallel with the relay coil to increase the load and keep the relay from a false start.

The system has been running about a month, and works to my expectations, with more than enough vacuum and velocity. One gotcha in my system is my paper barrel. I closed all of the valves with the shop-vac on and it imploded. Nice ad for Shop-vac I suppose. I'm not good at writing Dust Collector System With Shop Vac conclusions, or writing at all for that matter, so I end here I guess. I'd be happy to answer any questions.

I modified the circuit by replacing the original relay with a single contact relay and replaced the ohm resistor with a 40 watt light bulb. It has ran well since then, with no false triggers, but I have procrastinated updating this site. I also added a wall switch directly across the Aprilaire current sensor to aid in shop cleanup. The switch energizes the relay to start the vacuum directly, so I can connect a 20ft hose to clean the floor. Looking around the one that worked the best was a swimming pool skimmer.

Live right I guess. The hose reaches everywhere in the shop, even the cobwebs in the corners, and standard attachments all fit. I left the valve on the other side of the room, true it's not quite as handy, but can I reach it easy this way and this lets me put the flexible vacuum hose high on the wall for the swivel path of the saw.

I also ran a dedicated outlet on the wall for the saw from the sensed circuit across the room for the other tools on the vacuum system. Again, since I only use it for one tool at a time, there is plenty of capacity of both the electrical and vacuum system. Thanks, Steve. Steve - great idea and thanks for sharing.

I've been exploring how to build one of these and the pvc Y and valves are perfect. A couple of things I did that may be of help is 1 bought a remote outlet that I can carry in my pocket and can start the vac from anywhere in the shop which is really handy at least as long as you don't take it back into the house with you : 2 check out this video for a dust collection bucket which I've found to really work well.

Maybe smaller than you'd like but may be helpful for others. Reply 4 months ago. Question 2 years ago on Introduction. Question 3 years ago. Do you feel your shop vac has enough suction to handle the length of tubing you have? I am thinking about using a 6. My run will be feet before connecting to tablesaw etc. Also I am thinking on putting vacuum in a noice preventing cabinet. Do you feel it will over heat? I currently use the Dust Deputy atop a 5 gallon pail before going to my shop vac. I recently bought the HF 2 HP dust collector system.

I really like your set-up. For a hobby wood shop, I wanted to start my shop vac with a remote. I don't do electrical and didn't want to spend a lot of time and money on this. Amazon carries now a lot of outlets with remotes, but my shopvac is 15amps, 6.

Comes with 3 separate outlets labeled 1,2,3 and a remote with 3 buttons to operate these outlets individually.

Works through walls and other obstructions. The Harbor Freight link won't paste here. Search for Indoor Wireless Remote System 3pc.

Item I found this through a youtube video where the person went to HF and found a Stanley brand equivalent, but I had no luck finding that online or at HF so settled for the house brand.

Watco Stain Retailers Job Wolf Plunge Saw Blades Quotes Basic Woodworking Projects To Sell Online Drawer Roller Track Question