Powermatic 15 Inch Planer Manual Api,Shelf Design Woodshop Singapore,Salad Bowl Finish Canada Market - Videos Download
Manusl Of Contents. Quick Links Planrr this manual. This Manual is Bookmarked. Table appi Contents. Previous Page. Next Page. M Ph. Page 2: Warranty And Service This warranty covers only the initial powermatic 15 inch planer manual api of the product. The Five Year Warranty does not cover products used for commercial, industrial or educational purposes.
Products with a Five Year Warranty that incch used for commercial, industrial or education planef revert to a One Year Warranty. Page 4: Warning Warning 1.
Read and understand the entire owners manual before attempting assembly powermwtic operation. Read and understand the warnings posted on the machine and in this manual. Failure to comply with all of these warnings may cause serious powerrmatic. Page 5 Make your workshop child proof with padlocks, master switches or by removing starter keys. Give your work undivided attention. Maintain a balanced stance at all times so that you do not fall or lean against the knives or other moving parts.
This manual contains instructions on installation, safety precautions, general operating procedures, maintenance janual and parts breakdown. This machine has been designed and constructed to provide years of trouble free operation if used in accordance with instructions set forth in this manual. Page 7: Unpacking Unpacking Open shipping container and check for shipping damage.
Report any damage immediately to your distributor and shipping agent. Compare the contents of your container with the incy parts list to make sure all parts are intact. Page 8: Electrical Connections Electrical Connections Electrical connections must be made by a qualified electrician in compliance with all relevant codes. This machine must be properly grounded to help prevent electrical shock and possible fatal injury.
This machine must be grounded. In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric powermatic 15 inch planer manual api. Page 9: Belt Tension Belt Tension To adjust tension of the belts, open the rear panel and use the nuts A on the threaded shaft, shown in Figure 4, to either raise or lower the motor.
Re-tighten nuts when satisfied. Page Depth Of Cut Proper grinding done at the right time will do more ibch anything to prolong the life of knives. Page Feed Rate 4. If the reading on the depth of cut scale is incorrect, loosen the two mounting screws on the clear plastic plate and adjust accordingly. The top scale A, Fig. Page 12 NOTE: If a bed and feed paner gauge is plwermatic available, use a finished block of wood with notches cut out for the table rollers, and a feeler gauge.
See Figure powermatic 15 inch planer manual api for an example of a wood block used as a gauge. Page 13 Chipbreaker The functions of the chipbreaker are to break chips into small pieces, help avoid splintering xpi the wood, help avoid board bounce on thinner boards, and to direct the flow of chips out of the machine. However, should future adjustment be needed, proceed as follows: 1.
Place a bed and feed roll gauge or wood block powermayic one end of the cutterhead. Crank the planer bed up until the cutterhead is just touching the gauge, and check the measurement. Warping of wood is caused by uneven shrinkage during the drying process. Shrinkage is not the same in all directions of plqner grain and due to the different grain direction in pieces of Figure 19 lumber, different pkwermatic of warpage can occur.
Page Depth Of Cut Depth of Cut The thickness of stock run through the planer is controlled by the distance you adjust the bed from the cutting knife. Always start your work by making a light planing cut. Your PM15 planer-molder will accept a single knife set, which uses gibs and counterbalances to ensure the cutterhead is in balance at all times.
See Figure It will also accept a three-knife set. Page Pattern Knife Clearance 3. Mount the molding cutter gauge A, Fig.
The guide may be attached to either side. Adjust the gauge A, Fig. To adjust the guides, lower the bed and place a board of correct width ihch be molded under the cutterhead. Powermatic 15 inch planer manual api adjust the guides to the board.
Rotate the cutterhead by hand and see if the pattern knife will line up with the board. Adjust accordingly iinch the indh knife and board are lined up as in Figure Page Common Molding Applications If you have not already done so, install counterweights in the remaining two cutterhead slots. The rabbet knife is locked in place with the aluminum gib provided. NOTE: When the rabbet knife becomes dull on side, move rabbet knife counterweight set-up to the opposite side of the cutterhead.
Page Maintenance Multiple Custom Knife Use Many operators who have continuous short runs of several different patterns save set-up time by installing powermatic 15 inch planer manual api than one set of knives in the cutterhead at the same time.
You can change from one pattern to another simply by changing the guides. Page Lubrication Lubrication 1. The recommended lubrication for roller chains used in medium to powermatic 15 inch Powermatic 15 Inch Planer Parts Editor planer manual api speed operation is to simply wipe the chain clean. When there is an appreciable powermatic 15 inch planer manual api up of dust, dirt or wood shavings, use an oil cloth but never pour the oil directly on the chain.
Over-oiling defeats the purpose of the lubrication, since it powermatic 15 inch planer manual api to invite the collecting of dust, shavings, etc. Verify unit is connected to power. Check to determine if switch is actuating by listening for the audible click as hood is closed. If Poweermatic will not damage is seen, replace components. Inadequate support of long boards. Use extensions to support boards. Snipe Adjust feed roller tension.
Uneven feed roller pressure front to Note: Snipe can not be back. Page Replacement Parts Jnch parts are listed on the following pages. To order parts or reach our service department, callMonday through Friday see our website for business hours, www.
Having the Model Number and Serial Number of your machine available when you call will allow us to Part No. Description Size Round Head Screw M6 x P x 12Lg Hex Cap Screw Page Base Assembly Base Assembly Page Parts List: Gearbox Assembly Socket Head Piwermatic Screw Steel Ball Page Gearbox Assembly Gearbox Assembly Lock Washer Special Washer Page Stand Assembly Stand Assembly Left Support Plate Page 35 Set Screw Middle Table Handle Assembly Accessories: Knives and Moldings cont.
Page Electrical Connections Electrical Connections Print page 1 Print document 40 pages. Cancel Delete. Sign In OR. Don't have an account? Sign up!
Home Depot Ridgid Router Table Collection Wood Plans App Zoom |
SYRAX
13.11.2020 at 12:16:40
Efir123
13.11.2020 at 17:39:17
SimPle
13.11.2020 at 10:28:54
8899
13.11.2020 at 12:18:40
I_Like_KekS
13.11.2020 at 15:30:13