%!$ Easy Diy Woodworking Bench Plans For You #!@

kreg-jig-depth-collar-settings-pdf Did this summary help you? Secure the jig to the workbench. Added by Philip Miller. Screws alone make a plenty-strong pocket-hole joint, but adding glue helps prevent a joint from opening up due to seasonal shrinking and swelling. Place one end of the wooden board vertically against the clamp backing on the opposite side of the jig, then pull the lever to press the clamp tight against it. Cookie Settings. Several months ago, I purchased the Kreg K4MS so that I could build the Lego settinge as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.

For Technical Support, please call or send a message. Added by Alex DrMaster. Added by Philip Miller. Just got a rip-cut and installed my Bosch saw haven't used it yet but saw was a good fit. Got the original ripcut and didn't really like it had trouble cutting straight. New one has several improvements should make it work much better. Is the screw driver impact drill rated? Posted by Duke Leon on February 15, at pm. Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.

I have considerable experience with conventional…. Posted by Robert Ringel on September 17, at pm — 4 Comments. Powered by. All Discussions My Discussions Add. I have the Jr. Replies to This Discussion Permalink Reply by Rick on June 8, at pm Jay , some of us don't use those setup gages for the stop collar, in fact on my setup I can't use it anymore.

Trial and error? But this is not my situation. Put a nickle under the bit set it on that and your good to go. Yeah but Jens Jens Jensen said: Put a nickle under the bit set it on that and your good to go. I keep a nickle in the kreg box. Where the jig should be. You can also take and make a paste from flour and water and rup it on marks ,let dry and wipe off Rick said: Jay, I have the Mini, the Micro, and the K3, but not the Junior.

Need Help? RSS View All. Add Videos View All. Rip-cut ACS plunge saw Just got a rip-cut and installed my Bosch saw haven't used it yet but saw was a good fit. Is the screw driver impact drill rater? Add a Discussion View All. Product Reviews. Secure the jig to the workbench. Clamp the jig down so that it will remain firmly in place. Make sure the guide holes of the jig are facing toward you on the workbench. Part 2 of Clamp the wood into the jig.

Place one end of the wooden board vertically against the clamp backing on the opposite side of the jig, then pull the lever to press the clamp tight against it. Fit the drill bit into the guide holes in the jig. The guide holes should be just large enough to comfortably accommodate the drill bit. Most standard Kreg Jig models will have at least three guide holes so that you can drill as many holes as needed to support the joint. Should you need more pocket holes than your jig allows, you can make room for more by shifting the wood down in the clamp after drilling your first set.

Drill the desired number of Kreg Jig Drill Bit Depth Chart Pdf pocket holes. Pull back on the drill as you work to free the guide holes of loose wood chips. Drill as many holes as you need to create a strong joint that will suit the purposes of your project, then turn the board around and repeat the process on the other end.

Part 3 of Press the pieces of wood together to form a joint. Make sure the edges are evenly aligned. If you prefer, you can clamp the boards in place to make them easier to manage. Glue the edges of the joint together for added security.

Spread a thin layer of wood glue onto the edges of the boards where they connect. This will reinforce the joint even further and prevent the boards from coming apart as you fasten them.

If you're using wood glue in addition to a conventional clamp, apply the glue before you align the edges of the boards. Drill the screws into place. Drive the screws deep until they disappear inside the pocket hole. The pocket hole bit conveniently bores its own thread as it drills, so you should have no problem getting the screws to hold.

Finer threads should be reserved for hard, dense varieties of wood like maple and Kreg Pocket Hole Jig Settings Lyrics oak. Conceal the pocket holes with wood plugs or adhesive. These can easily be filled with a glob of putty or wood glue. You could also invest in a set of Kreg wood plugs, which are specially tapered to slide right in for a smooth, seamless finish.

Include your email address to get a message when this question is answered. Take proper safety precautions by wearing eye protection while drilling. Helpful 0 Not Helpful 0. Kreg Jigs are useful for mounting shelves, putting together wooden crates, making your own tables and cabinets or dozens of other woodworking projects. Helpful 1 Not Helpful 0. Use pocket holes to reinforce the joints in your favorite antique furniture pieces and increase their lifespan. Submit a Tip All tip submissions are carefully reviewed before being published.

Helpful 2 Not Helpful 0. Exercise caution when working with electric drills and other power tools. Carelessness can lead to accidents or injuries. Related wikiHows How to. How to. More References 7. About This Article. Co-authored by:. Co-authors: 4. Updated: November 5, Categories: Woodworking Tools. Thanks to all authors for creating a page that has been read 58, times. More reader stories Hide reader stories.

Did this article help you? Cookies make wikiHow better. By continuing to use our site, you agree to our cookie policy. Doug Allam Nov 28, Will Vrba Aug 25, It really helped me to explain to my 9 year Kreg Jig Depth Collar Settings Us old grandson how to successfully use my Kreg Pocket Hole tool.

Jointer Plane Functions Calculator Garden Bench Plans Metric 100 Jet Planes Korean War Mod Small Cnc Routers For Woodworking Limited