%!$ Easy Diy Woodworking Bench Plans For You #!@

danish-oil-on-walnut-plywood Hello, I want to use a Danish Oil Finish On Walnut King butcher block counter for a sewing table top. Thanks again Gary. And rub softly, pushing too hard will pull out more slurry too. Answer Upvote. Waxed finishes, and all dirt and danish oil on walnut plywood, should be removed with white spirit on a rag using vigorous agitation. The oill was left at room temperature for 48 hours before dqnish was used to allow the Danish oil to cure. Thanks for the comment.

But for the first half hour of drying, keep an eye on it to make sure no oil is seeping back out and pooling on the surface. Once that coat dries, if you still see any open pores, repeat the process with another slurry coat.

Once the coat has dried and it appears perfectly flat, apply a final thin layer to help seal in the slurry coat, or you can add a coat of wipe on poly to finish it up.

For extra protection, add a second coat of wipe on poly. Be sure to lay out the rags flat until they can dry, then throw them away..

If you make your own Danish oil, make sure the main ingredients have dryers in them, like boiled linseed or tung oil. Also, do not use non-drying oils like mineral oil. If you use turpentine, get the kind that is made from pine. This smells much better than other kinds of turpentine. When you mix your own Danish oil, do it in a glass jar with a metal lid. If you use a plastic container, oxygen can get into the mix and over time can ruin the finish. A glass jar sealed tight with a metal lid will have a longer shelf life.

They claim to follow FDA regs that makes it safe to use on kitchenware and toys. Thanks for stopping by, and be sure to sign up below so I can send you blog post updates, plus some free plans and templates. Beginning Woodworking? This page may have affiliate links. For more information see my disclosure page.

About The Author Adam has been woodworking for the last 10 years. He considers himself a 'Small Shop Woodworker' and practices his hobby in his garage.

With the lack of time, space, and proper tools, he always finds ways to get great results without over-complicating or over-thinking the process. Various shop jigs, table saw sleds, and tricks of the trade have served him well. God has blessed him with a beautiful family, as well as a passion for teaching others about woodworking.

You can read more about Adam here. A really helpful instructive article on using Watco Danish Oil finish. His method was to use the slurry method over a week and wiping off the excess as it dried between coats. Then let it dry over a week and wiping off the excess oil everyday that bleeds out over that week. I then used a pleasant smelling paste wax like Briwax. I use only this type of finish technique for all jewelry boxes and even applied it to a antique dresser that I still own.

Great tips Gary, thanks. And often a single slurry coat or 2 is not enough, so using different grits sounds like a great time saver. Thanks again Gary. Hello, I want to use a butcher block counter for a sewing table top.

I love the natural, light wood — it is Birch. Do you have any suggestions as to what I could use? To avoid changing the color of the wood, you want to avoid oil-based finishes altogether. I think what may be best for your project is called an acrylic lacquer. As with any new finish, test it out first on some scrap wood from the same material you used in your project.

Just stained butcher block with Danish oil for a laundry room countertop. What should I use to clean the counter? Liberally apply the finish over the whole work piece using a brush or rag. You can put on a lot, flooding the surface. After 30 minutes, come back to the piece and reapply finish, particularly to areas where all the finish has been soaked in.

For a typical piece of furniture I will repeat this process to build up 2 or 3 coats. Additional coats will deepen the shine and increase protection. Once I am satisfied with the number of coats, I will wait 15 minutes, then wipe the surface of the piece completely dry making sure there are no drips or pools of finish.

I will touch the finish with my fingertips - it should feel oily but dry and smooth. You must now safely dispose of the oily rag.

Improperly disposed oily rags can spontaneously combust. Hang them outside to dry in a safe area or spread them out flat. They should not be in a pile. Once they cure, the cloth will be hard and brittle and you can throw them out. Question 2 years ago on Introduction. Can I soak new cut plywood scroll saw pieces in Danish oil overnight? Or, dipping it in a tray for 30 minutes? Question 3 years ago on Introduction.

Hello and thanks for the video information. My question is I noticed that you did not sand between coats, is it necessary or not? I am making an unfinished acacia wood butcher block, L-shaped bench for my breakfast nook that will be built-in. We want something to seal it with something that does not change the color much, yellow like polyurethane and not a glossy finish.

We would like to keep it as close as we can to its natural color, maybe a matte or satin finish. We will sand and seal the wood prior to building in a shop, and prefer not to do much sanding in our home now and in the future.

We would like some advice Thank you so much for your time! To avoid premature evaporation, I decant the oil into smaller bottles, in which I aim to have as little air as possible.

A hassle, but before I switched to this method, I lost half a tinfull due to over-long air contact. Reply 5 years ago on Introduction. Thanks for the comment. The process I described is commonly called the 'one day' finish - flood it one and come back reapply successive coats in the same day, then wiping it off.

Another way to do it is to wipe on a thin coat, then come back the next day in 8 hours or whatever and do another thin coat. In my experience Danish Oil Finish On Walnut 2019 both work well. I don't generally put finish back in the can - I try to one take out a bit at a time to make sure I'm not wasting any.

Thanks for the tip on evaporation, good to know! Reply 3 years ago. I know this is a really old comment, but thought I would share a tip for any new people stumbling over this great instructable. Instead of moving the oil over in smaller containers, it is possible to fill up the can with marbles. This will fill up the empty space and thus removing the air in the can.

Woodworking Dust Collection Parts Examples Wood Track Drawer Guide Jpg Best Jay Z Rap Quotes Tab