%!$ Easy Diy Woodworking Bench Plans For You #!@

My next few posts are going to tackle the dust collection system for my workshop. I have just finished building my handtool bench and have amassed a fairly comprehensive set of handtools, but Dust Collector Pipe And Fittings have no intention of going handtool only.

I love having a good jointer and planer for stock preparation, and a bandsaw and tablesaw are great workhorses that I have no desire to part with either. There is, of course, a setback to using cpllector big power tools… They make a lot of dust. Be it for health reasons, or simply to keep the shop clean, the use of large woodworking ,e usually necessitates the use of a dust collection system. My current dust collection system can only be described as less than ideal.

The equipment that I have is good, but it needs to be set up with some better organization and logical planning. As it is now, I have to bring the tool to the dust collector. I want to get to a point where all my major tools are stationary and plumbed in to a dust collection system. I like the idea of using a separator or cyclone to remove most of the wood particles before they enter the dust collector.

The main reason for this nar that the plastic bag on the bottom of the collector is such a pain to empty. To be perfectly frank, this lid is crap!

If I get any more than about 6 inches of dust in the bottom of the can, the air turbulence in the trashcan prevents it settling out. Dust collector pipe and fittings near me pjpe the dust ends up in the collector, which is what the trashcan separator is supposed to prevent in the first place. This should be solved by the addition of a Thien baffle. Having the metal trashcan sitting next to the dust collector nearly doubles the floor space that it takes up and makes it awkward to move.

Ideally, I want the trashcan to sit underneath the dust collector. So, dust collector pipe and fittings near me goes. First up is the trashcan separator.

To start the lid, I got some of these pieces out. The metal trashcan that I am going to adapt with a Thien baffle. The top of the lid consists of two pieces of plywood, one that fits just inside the top rim, and another that is slightly larger than the rim.

I cut a third piece of plywood to a slightly smaller radius than the others. This is to reflect the fact that the trashcan tapers and gets narrower a towards the bottom. This dust collector pipe and fittings near me is the actual baffle that should allow particles to settle to the bottom of the can without being sucked back up and sent on to the dust collector. The third piece of plywood is the actual baffle.

The third piece will be mounted about 8 inches below the lid. I used a pair of dividers to space out the three nar holes evenly. I used a pair coplector dividers and adjusted them until my third step brought me back to my original starting point. One the hole locations were marked, I drilled them at the drill press and then laid out the 4-inch holes for the PVC pipe and fittings.

I cut the hole on this piece slightly under size and adjusted it on a spindle sander until a 4-inch dust collector pipe and fittings near me of pipe fit snugly. To cut the holes in the separator lid, I first drilled a hole, then using the jigsaw, cut it being careful to stay inside the line. That left these two holes in the lid:. I added the 6 Dust Collector Fittings Zone copper pipe spacers, washers to prevent them sinking into the wood, and the PVC pipe and fittings.

I glued the pipe in place using PL construction adhesive fkttings from Home Depot. I like this dust collector pipe and fittings near me, it takes a long time to cure about 24 hoursbut is very strong when done.

Next, I turned my attention to mounting the dust collector to the wall. I disassembled the dust collector and removed the steel base and wheels. I bought some heavy duty bracketsalso from Home Depot. I had quite a few of these dust collector pipe and fittings near me over from when I used them to mount the vise hardware underneath my workbench.

I bolted heavy duty brackets to a piece of plywood and then lag bolted that plywood to the wall studs. It needed a small notch on the left side to allow my sheet good storage bin to fully swing closed. I also notched the back of the shelf for the upright dust collector pipe and fittings near me column and cut a semi-circle out from the right side.

This will allow the trashcan separator to slide underneath the shelf and thus reduce the overall footprint of the system. The shelf is attached to the figtings by bolts and to the backer board by screws.

I lifted the dust collector onto the shelf and marked the location of the mounting holes. After drilling, I bolted the dust collector to the shelf. A shelf is installed with a cut out for the trashcan. I bought some cheap swivel casters and attached them to the bottom of the trashcan. This should make it a little easier to pull out dust collector pipe and fittings near me empty the can.

I added some swivel casters to the bottom of the trashcan. To attach the casters, I cut three small pieces of metal from some scrap flashing and drilled holes in them to match those in the base of the swivel casters.

These were installed on the inside of the trashcan and collectkr as a type of washer to co,lector and stiffen the connection between the casters and the metal base of the trashcan. I used small pieces of sheet metal over the holes on the inside of the can. Are some of the PVC fittings left loose for this purpose? As far as emptying the can, the pipe fittings are left loose.

You lift off the intake and exit pipes dust collector pipe and fittings near me cittings Dust Collector Fittings And Accessories can rolls out. That thing drives me crazy. Nera is simply superb work. I really like the photo of the inside of the trash can. It has a certain je ne sais quoi! One day when I am all grown up I hope to also add something like this.

For now the wood is becoming part of me by getting lodged in my lungs. At this rate I might be able to znd something using my lungs as stock in the not too distant future. When it is my turn to install a system like this, I will certainly consult you and this series of posts. Is funny how much alike we continue to think. I really like that photo too. A Gerhard mantle clock??? Skip the remote switch. I have a similar Grizzly unit, v.

I purchased a wireless RF Remote Control that you can carry on your belt anywhere in the shop, instead of walking over to a switch.

Grizzly sells it in both v and v versions. Good luck. I guess I should have been a little more specific, but a wireless remote switch is exactly what I had in mind. Finding the time to write is increasingly difficult. I ended up wiring a v remote to a v contactor. I hope to have that post up in the next few days. Curious to hear how your new cyclone separator works.

If it still leave something to be desired, trash it and get the cyclone lid from Lee Valley. It does not have the drawback of similar design like the Grizzly. Dust collector pipe and fittings near me mine ever dust collector pipe and fittings near me it came out, and really dust collector pipe and fittings near me it, no complaints.

Pingback: Roubo sharpening bench — part 8 Je ne sais quoi Woodworking. This site uses Akismet to reduce spam. Learn how your comment data is processed. Enter your email address to subscribe to this blog and receive notifications of new posts by email. Email Address. The Bench Blog. Skip je content. My current dust collector setup. Glued, clamped and left overnight to dry.

Adding washers and carriage bolts. After adding the rest of the parts. With the PVC ducting added. Like this: Like Loading I buy too many tools and don't build enough - I need help! This entry was posted in Shop Projects and tagged Dust Collector. Bookmark the permalink. May 26, at am. Jonathan says:.