Drawer Lock Router Bit 2000,Custom Wood Burning Stamp,Jet Planes Lollies History Youtube - Easy Way
I'm in the middle of building a nightstand. As part of that I needed to make several drawers. There are many ways to make a drawer. I'm not about to say one way is better than another. For this project, I chose to make my drawers using a small drawer lock bit. As part of that, I decided to document the process and present it here. I'm using a small drawer lock bit from Lee Valley Tools. I've looked around online and there are several similar kinds of drawer lock bits available from different vendors.
The cool thing about this method is that all locck the drawer joint cutting operations are accomplished with ONE router table setup. There are instructions on loock Lee Valley website. First, the router bit is set to the depth of one quarter inch, which is half the thickness of your stock.
Next, you set the fence so that the middle of the angled part of the bit falls at the middle of your stock. This is of course a tricky setting, so you will definitely need to have some scrap wood available for making drawer lock router bit 2000 cuts. In these photos I am making a test cuts on scrap wood, which is an identical thickness to my drawer pieces. The two cut pieces then fit together like this final photo locking together.
This is my fourth test piece. So I rputer to adjust drawer lock router bit 2000 fence four times to get a nice flush fitting joint. Considering how rudimentary my fence is, I think that is pretty good. If you try this, just remember to 2000 several pieces of scrap available for test cuts -- or just one long scrap piece, which you just keep cutting down shorter.
With the router table properly set up, I proceeded with batch cutting all of the drawer pieces. In order to keep things from getting messed up, I first lay out and cut all the drawer fronts and backs You need to be careful with the sides, to hold them perfectly perpendicular with the end flat on the table as you cut them. I had a few mistakes where the piece tilted a bit as I pushed through the cut, and I had to re-do those pieces.
I then moved on and cut rabbets along the bottom of the drawers, to h hold the bottoms. I cut the back of the drawer shorter, so that the bottom can slide in and out. I also cut out the bottoms. None of that was filmed, as the focus of this article was just on the joinery. With the drawer pieces ready, it is now just a matter rputer adding glue blt the ends and then alinging and clamping the pieces.
I slid in the plywood bottoms immediately, as they help with ensuring that the drawer box is Drawer Lock Router Bit Instructions Jump square. Here is one shot showing a drawer lock router bit 2000 tight drawer corner joint. The two drawer pieces lock together securely, and the joint is closed and flush. In the interests of full honesty, here is vrawer a photo of one of my Fortunately this joint was 20000 the back of a douter where it will almost never been seen.
Otherwise I would drawer lock router bit 2000 to fill this with sawdust and glue to close the gap, or redo the joint entirely.
Note that thet joint is still strong, it just is a bit ugly. I suspect this might have been caused by those problems I had with the lck pieces wiggling a bit while being cut on the router table. And that is all for now. Drawer lock router bit 2000 drawwer was just about a drawer joinery method.
I hope you found rouuter useful in this article! This is a simple drawer joint, and after initial setup you can cut out your drawer joinery very quickly. Note that the drawers are by no means finished at this point.
This is rojter the drawer draawer. Later on I will be adding nice fronts to these drawers. Thanks for reading. For more projects, going back years, please visit my woodworking web site at www. I love the comic relief you've integrated into the video As well as the educational part, considering the name of this place.
Introduction: The Drawer Lock Joint. By wordsnwood Drawer lock router bit 2000 N Wood Follow. More by the author:. About: I build, I write, I film Mostly a woodworker. More About wordsnwood lcok. Drawer lock router bit 2000 you would prefer, you can watch a video of this tutorial.
Otherwise, read on. Did you make this project? Share it with us! I Made It! Incredible Wooden Spirals by rschoenm in Woodworking. AgHans 5 years ago. Reply Upvote.
Makita 2301 Router Table 3d Belt And Disc Sander Makro 93 |
BlatnoY_VoR
21.02.2021 at 12:14:21
rayon_gozeli
21.02.2021 at 22:16:30
KAROL_SKARPIONOV
21.02.2021 at 20:12:16
Turchanka_18
21.02.2021 at 15:59:28
BlatnoY_VoR
21.02.2021 at 11:57:24