Watco Salad Bowl Finish Volcano,Combination Lock For Kitchen Cabinet In,Router Table Sled Plans Guide - Downloads 2021
Please read the new sticky announcement HERE for full details. Forums New posts. Photo Gallery New media New comments. What's new New posts New media New media comments Latest activity. Members Registered members Current visitors.
AAW Main Site. Log in Register. What's new. New posts. Log wwtco. Install the app. We just finished a major forum upgrade. Hope you enjoy the refreshed site! Welcome new registering member. Your username must be your real First and Last name for example: John Doe.
Also, do not use all caps nor all lower case. JavaScript is disabled. Bow, a better experience, please enable JavaScript in your browser before proceeding. You are using an out of date browser. It may not display this watco salad bowl finish volcano other websites correctly. You should upgrade or use an alternative browser. Watco butcher block finish used for bowls blochiness. Thread starter Phillip Medghalchi Start date Jan 28, Tags finish finishing problem finsihig with watco butcher block problem walnut bowl.
Phillip Medghalchi. Hi, every one, I have a problem with this finish and am hung up for an answer to remedy this for almost more than a month. I have taken this bowl to the local club and called and talked to some of my friends whom I respect their knowledge n our trade. Here is the situation I have used this produst in the past with good success and did not have any problems with it bloching. However, this time using it on watfo Walnut that came form CA and I have all the frieves one can take, with it.
Boql, I contacted the Rustoleum and they did not give any help. So, Watco salad bowl finish volcano am hoping some out tere tried this product and can give some tips. Please note that I have tried spot sandig where it did not take the finish and went down from grit to grit, and tried to apply it little thicker to have wood take the finish, but to no avail. I have wet sanded at one stage with mineral spirit as it states on the can for cleaningno satisfactory result.
I have applied DNA and that didn't help watco salad bowl finish volcano. Applied acetone as Rustoleum rep told me so.
Finisb, also, the can says to apply it to raw wood which I think in this case it was a mistake doing so, since Walnut is open grain wood and the end grain is much porous. I am trying to not resort to putting it back on glue block and sanding the whole thing to bare wood which is fniish going to watco salad bowl finish volcano that easy and then start the finish all over again.
I appreciate any help. Last edited by a moderator: Jan 29, Volcanl Beasley. What I see is end grain absorbing heavily as well as some area of fine tearout making the dull patches. You might need to wash the finish off and sand everything to get rid of the tearout. Not sure if the area that got dark from over absorption will lighten up but the look wont be as bad as you think once the finish is even. Richard Coers. It's really tough to get a film built up when you are using that much thinner.
You'll have to put on ealad 20 coats tif you want a film build up. Was the wood dry? Last edited: Jan 28, Bill Boehme Administrator Staff member. Beta Tester. It looks like you aren't applying the Watco Butcher Block Finish as intended. It is basically thinned tung oil with some resins. I would prefer using a straight oil finish, but this product can be applied the same way: apply with a rag, rubbing it in and then let it sit for about ten minutes.
Next, use a clean rag to wipe the surface dry. Wait about a half hour and then wipe the surface again to remove any watco salad bowl finish volcano the finish that has seeped out of the pores. It appears that you might have applied really heavy coats and then let it sit like you would if Watco Salad Bowl Finish Yellow applying a varnish. I like walnut oil.
It's quick and easy and doesn't darken the wood as much as linseed oil or tung oil does. And, it smells nice. I don't care for layering different types of finishes so I wouldn't normally apply a film finish over an oil finish. HOWEVER, if you do want to follow the oil finish with a film finish, I would suggest waiting several weeks to allow time for the oil to catalyze. I see a lot of deep sanding scratches. Don't skip grits watco salad bowl finish volcano sanding.
PS: Each image finishh posted three times. I removed the duplicates. If you see an error like this, you have the watco salad bowl finish volcano to go back and make corrections. Doug Freeman. This watco salad bowl finish volcano is very similar to minwax wipe on poly, with tung oil instead of linseed oil, which doesnt effect the application process.
Both use alkyd resin and are approximately the same solids. I dont know how hard the watco oil will get with alkyd solids it should harden reasonably well. The issue I see is the wood surface was not uniformly sanded before finish application.
It sounds like your application method is to apply a film with a brush and walk away. If correct, I would watco salad bowl finish volcano to see exactly what the pics show. This is not blotching. Its a dry film finish on the shiny areas, And no or insufficient film thickness in the rough areas. I see 3 possible paths forward: 1 keep adding coats Watco Salad Bowl Finish 12 and sanding back until the rough areas start to bridge and build a film.
These areas will watco salad bowl finish volcano look great but ok. I use a lot of wipe on poly. Besides getting a better, more consistent sanded surface, something Watco Salad Bowl Finish Zip finizh will help is to apply a couple of coats like danish oil - flood on, keep wet for min, wipe off. This will seal the Watco Salad Bowl Finish Line surface. Then watco salad bowl finish volcano a brushed film which will dry more uniformly on the surface.
Whether to remount depends on whether you prefer to sand on or finizh the lathe. Last edited: Jan 30, Watco salad bowl finish volcano Beasley said:.
Click to expand Hi Richard Coers said:. Roger Wiegand Beta Tester. Phillip Medghalchi said:. I did look at the MSDS and although that I am not clear about it, I see that most of it indeed is toxic chemicals, and I am not sure how they say it's food safe finish? Greg Norman. They said I was not wiping off the excess well enough. I tried doing a better job of wiping it down after flooding and waiting a bit. I did get better results on some bowls but no matter what I tried I still had some that looked similar to yours.
I now only use walnut oil on food contact items and never have any problems. Roger, i appreciate your insight and the tip. The main issue for using this product was that to put on a finish that's food safe and FDA approved. I have used this product in the past on Mesquite and Bradford Pear that Bill can attest to it, since he is in the same general area that I voclano. What I was trying to figure out was why is it doing it on Watco salad bowl finish volcano and volczno there any more preparation that was necessary that I failed to do.
I followed the can's instruction and applied the finish directly on the raw wood which now I realize form above posts that I made a mistake and did not seal the wood watco salad bowl finish volcano applying the finish. I also, noticed that it was best to put it on and wife off the excess and come back wipe it again until I build up a nice finish.
Rockler Workbench Casters Uk Price Wood Veneer Finish Repair 90 |
bakililar
11.05.2021 at 18:58:59
Gentlemen
11.05.2021 at 10:42:11