%!$ Easy Diy Woodworking Bench Plans For You #!@

waterlox-countertop-sealer And also what cleaners would you recommend to extend the life of our butcher block island waterloxx. The last coat is a bit nerve wracking — I know. Having done a few of these countertops I now know what the final coat should look and feel like. Seems we are back now which is great. I did do a rehab project waterlox countertop sealer a really old dining room table a couple waterlox countertop sealer years ago. Watrelox so, do you have the veneer countops or the completely wood ones? Support Purchase Contact.

Did that once and left behind glops of dried Waterlox. I have also left behind bits of foam brush when I tried to use one twice. Why bother? Just throw out the cheap brush and move on to a fresh new one.

I start saving up containers as I approach Waterlox go-time so that I can pour out just enough Waterlox for one go-around on a countertop, and then I toss the container along with the brush. If you have to re-use a container wipe it out thoroughly with a dry cloth when you are done with a coat. If you allow the Waterlox to dry in the container, and then try to re-use the container, you are pretty much guaranteed to get glops of dried Waterlox in the next coat. The quart-sized Waterlox Original Sealer comes in a rectangular can.

Crinkle up the can as you go. This pushes air out of the can which would otherwise dry out the product. Well, wrong. Pour the Waterlox out of the can in the way shown in this photo but take the cap off, of course to keep the Waterlox Original Sealer Jacket stuff from pooling on the top of the can, making the screw cap harder and harder to twist off as the layers of Waterlox dry in the cap grooves.

As they state on their website, Waterlox penetrates deep into the wood. It has a consistency closer to water than to, say, polyurethane. I suppose this depends on the wood Waterlox Finish For Wood Countertops Equipment you are Waterloxing but for both the Ikea and Menards butcher block I worked with the stuff really soaked in. I lay my second coat on thick too. After this coat dries you will need to sand. Sanding between coats from here on out is absolutely the key to getting a super smooth finish.

I sand with grit paper , then wipe the entire surface down with a clean damp rag and then I wipe everything down again with a clean dry rag. I look for dull areas going into a new coat. Waterlox will self-level if you put enough on. I find that you have to work a little quicker with the Satin Finish. It just seems to set a little quicker. Definitely do not touch up as you go see Tip 8. That final coat is so satisfying to put down and when it dries it has a gorgeous feel to it.

Your butcher block will look amazing. Okay so this tip is about purchasing butcher block, not applying Waterlox. Ikea stopped offering 1. Also, did you know that you can get butcher block through Amazon? Now you do! Have you used Waterlox on butcher block? Love it? Hate it? Please share your experience in the comments!

My husband and I have researched how to refinish our maple island top and you wrapped it up for us in detail. Thanks again! Thanks for your comment Charolette! I hope your maple island top turned out great! Hi Sara — thanks for visiting and for the great question! Hope that helps!

Can i Waterlox Sealer Dry Time just seal the sink well and not worry what the inner walls where the sink cutout is? Or will i need to cut up the caulking, pull the sink out, and seal the inside cutout? Hi Nathan — First off apologies for the delay in this reply. Seems we are back now which is great. If the sink in question is in a rental unit, I might re-do it, coat the cut-out, have peace of mind.

Thanks for the specifics. I made my list and will refer to this! Now to see if Ace carries Waterlox. I am considering staining it first since I like either lighter wood or darker and not as crazy about the medium shade.

Hi Alicia — thanks for writing! I have only ever seen Waterlox online. I think Amazon was able to get it to me a little quicker and with Prime I got free shipping. The color will change a little with the first coat of Waterlox, and then deepen with time.

Your project sounds great and I hope my tips help to make it go smoothly. Good luck! Fantastic details! Thank you for your tips on how to apply Waterlox. Getting ready to put my Satin Waterlox last coat on now. I also appreciate the post on how the countertops have held up and cleaners to use. Thanks for taking The time to post and help the rest of us DIYers!!!

Thanks so much for the comment Kirstin. So glad this post helped you crush this DIY project! So satisfying. Using the right cleaning products is truly key. Enjoy your countertop! Hi Nathan — thanks for your question. Will check it out! Thanks for the info! I have had 5 coats of Waterlox on my butcher block counters for two years.

I have a problem with any stickers on the counter or even magazines sitting on it for more than 1 minute. When I go to pick up the sticker or magazine, it is firmly stuck to the counter, and I have to soak and scrape it with a credit card.

In some cases, the finish has peeled up all of the layers leaving a big, highly noticeable spot. Do you have this? How can you stop or fix it?

Hi Eric — I have not encountered this problem to the extent that you describe. I have experienced a very stepped back version of ink-transfer with glossy magazine covers. But a few spritzes of a natural cleaner, let it set for a minute, and then a wipe up with a paper towel has taken care of things for me. I have never had to soak a spot for more than a minute and I can see the ink lifting off in that minute.

I would absolutely reach out to Waterlox and tell them about this. Thank You! Being a contractor, I appreciate the level of detailed advice you give on this project. Really well done PC. I have one tip to give regarding storage of Waterlox after each coat. I pour it in a saved and dishwasher cleaned pasta sauce jar. Then place a piece of saran wrap with a small dime sized hole cut in the center, on the top of jar. And I have a vacuum sealer universal lid that I put on top of that and suck out all the air in the jar.

Thanks again,. Crushing the can is effective but then the can wants to fall over. Your method sounds more stable for sure.

I actually have wondered about preserving the satin finish product which comes in a wide-mouth can. This has been so helpful!! Thank you so much. I have applied 4 coats of the original waterlox over the last week onto my butcherblock, and am preparing to put the final coat of satin finish on today. Do you recommend a foam brush for that?

Hi Brooke — I do recommend a foam brush be used for your last coat. Put enough down so that it glides over the top. The last coat is a bit nerve wracking — I know. But you got this Brooke! Thanks for your question! Hi, thanks for the tips! I got a poplar piece that has some shades of green, does the green color soften with the waterlox application? Hi David — Thanks for commenting! I have only ever put Waterlox on birch butcherblock.

I did do a rehab project on a really old dining room table a couple of years ago. I removed a peeling veneer and underneath that was poplar boards. They were very green which I liked, but then I coated with a water-based polyurethane and the color changed a bit. Over time, the green has all but disappeared and the top got much more tan in appearance. Still nice, but I did love the green. All rights reserved. What is Waterlox?

Pure Tung Oil. Not Sure What Products to Use? Get Started. Need Application Instructions? Find the appropriate application guide based on the products and surface size you are using. Find Guide. Running Into Problems? Search Now. About Products Project Types.

Mallet Hammer Home Depot Online Benjamins Best Lathe Tools Review Keyboard Best Woodworking Clamps 60 Best Router Bit For Cutting Fiberglass