%!$ Easy Diy Woodworking Bench Plans For You #!@

pure-tung-oil-brands Приобрёл в известном инет-магазине Pure Tung Oil от Rustin's, разбавил немного 50/50 с очищенным уайт-спиритом, купленным в художественном и, в качестве эксперимента, пропитал поделку, из неизвестного, не плотного, дерева. Деревяшка пропиталась насквозь, подождал полчаса, стер остатки салфеткой и оставил сушиться при комнатной температуре. Через 2-е суток решил положить второй слой, но обнаружил что масло даже не Tung Oil Nz University подсохло! так-же как и кисть. Полез в инет, информации о подобных случаях не нашел и стал грешить на "очищенный" уайт-спирит. Потом решил пропитать не разбавленным. Хор. Тунговое и тиковое масла известны уже не одно столетие, а датское с середины прошлого века, но в нашей стране широкого распространения не получили. Причины этого весьма прозаичны – в наших широтах не растут те деревья, с которых их можно получить, и как следствие цена на них выше чем на банальную морилку. В чём же собственно отличие данных масел от более привычных нам средств для древесины? Ответ на этот вопрос очень прост – во-первых в том, как масла раскрывают текстуру древесины, во-вторых в глубине пропитки. На внешний вид второй пункт практически не влияет, а вот для срока эксплуатации - э. Марки тунгового масла. Наиболее популярным считается масло Borma Tung Oil (Италия), которое производят в упаковках по мл, 0,5, 1, 5 литров. Стоимость за литр — – рублей. В смеси с льняным, тиковым маслом, со щелочами и красками продукт стоит на порядок дешевле.  Выбирать масло, на упаковке у которого указано % или pure, если надо выполнить тонкое, натурального вида покрытие. Покупать масло polymerized tung oil, если требуется сделать густое покрытие с глянцем. Если отмечается зеленый оттенок продукта, его качество снижено, а самое высококачественное масло имеет медовый цвет. A lot of users are using these regularly and so far they seem to be good with them. The answer is yes and no at the same time. Continue Reading. Pure tung oil brands, it is moisture-resistant as well. And the oil does not get dark as time passes. These oil makes the wood highly durable and makes them moisture-resistant as well. Thread Modes.

I started with absolutely nothing. Now, thanks to years of hard work, careful planning, and perseverance, I find I still have most of it left. I might give that Hope's stuff a try. Wildwood Member. Most people thin Tung oil with either mineral spirits or citrus solven to increase penetration and speed up drying.

Hi again Kingwood Second, 'pure' tung oil will take longer to dry vs. BLO but certainly 'not forever'. I'm only using the oil for color-deepening under a water-based topcoat. Ordinarily I'd use an oil-based poly, but those take longer to cure, so I'm doing it this way. Well, I've used 'tung oil' just a few times - more often, the thirds combo finishing formula i. Others may have a different opinion? MKepke Member. Thinning it will help. You can also add a tiny amount of Japan Drier - it catalyzes the cross-linking and expedites drying.

It will itself also darken the tung oil a bit. Note that Japan Drier is toxic as is MS and will negate any non-toxic properties of pure tung opil, if those are important to you. Lee Valley gives some guidance on tung oil dry times. Some facts to think about: Most top coat oil or water base finishes will high light any grain or figure present in Tung Oil Application wood.

All manufacturers or vendors will tell you thinning pure tung oil aides in penetration and shortens drying times. If given enough coats 4 to 5 get some build of protection.

Commercial oil varnish blends can contain less expensive semi-drying oils thanks to chemistry. Only required to list hazardous components! You do not get more protection no matter how many coats you apply due to diluting the resin! Some commercial blends will give you more sheen than others or home brew mixes. Many commercial products listed as tung, teak, or danish oil are wiping varnishes! Among natural finishes, tung oil surpasses shellac and linseed oil in hardness, durability, and water resistance.

While there are many advantages to using it, pure tung oil takes two to three days to harden, and needs at least five Tung Oil And Beeswax coats. For help picking a finish, see below. They all share the benefits that tung oil imparts to a finish—durability, water resistance, resilient hardness, and color stability—depending on how much of the oil they actually contain and what form it takes.

Pure tung oil is easy to identify because it contains no solvents. That may be a good thing in terms of limiting your exposure to VOCs, but applying it is an exacting, drawn-out process.

You have to wait at least two to three days for each coat to harden. And it takes five to seven coats to get a protective film. Rushing the process, or applying too thick a coat, causes wrinkling, which has to be sanded off. The results can be gorgeous, as long as you have the necessary patience. Both types do this by adding man-made resins and solvents to keep those resins in solution.

The difference between these two is subtle. Blends consist of an oil or oils mixed in with a varnish. A varnish is made by cooking resins in a hot oil until resin and oil form a chemical bond. Wiping varnishes are just what the name implies—straight varnishes that have been thinned enough to be wiped on with a cloth.

Fig Wood For Turning 60 Router Jig Templates Example