%!$ Easy Diy Woodworking Bench Plans For You #!@

parts-of-a-wooden-hand-plane-kit Hock Krenov Style Wooden Plane Kit

Of all the tools you use to shape wood, the hand plane is the one that has come to symbolize craftsmanship of the highest order. And it's no surprise. Here's a cutting tool that's designed to create truth: dead straight and flat surfaces ready for finishing and precise joinery.

Tuning one up and mastering its use Parts Of A Wooden Hand Plane 15 are two of the greatest thrills of woodworking. But, if you really want to bring the planes in your shop to the next level, it's time to make your own.

Our interpretations are easily built, and the basic design is well-suited to modification so you can make planes that match parts of a wooden hand plane kit needs.

We offer three sizes: a block plane, smooth plane and jointer plane, all based on the same shape but each with a different-size cutter iron. We used irons specifically designed for wooden planes, available from Hock Tools, Mitchell Creek Dr.

Each iron comes with a cap iron and assembly screw. While many woods are suitable, we chose cherry for the bodies and wenge for the soles of our planes. A sole isn't absolutely necessary, but a hard, dense wood resists wear on the bottom surface.

Try to select stock that allows you to orient the grain vertically in both the plane body and sole to provide better dimensional stability. Click on link for high-resolution version of the plans. Illustration by Eugene Thompson.

If you're going to make more than one plane, it saves parts of a wooden hand plane kit in machine setup to make them all at once.

First rip and crosscut the body blanks to size as shown in the plans. Take care to ensure that the blanks are perfectly square in cross section.

Glue the soles to the body blanks. When the glue sets, scrape off any squeeze-out and trim the soles flush. Then, measure from those marks to lay out the angled internal shape.

Use an angle gauge to lay out the cuts, and saw to the waste sides of the lines on a band saw. Use a razor-sharp block plane to plane the sawn surfaces of the body blocks so they're square to the sides of the blocks. Work carefully because the results will affect the performance of the plane. If the back block is not flat, the iron will rock or chatter in use. Clamp a support block so that its surface is flush to the angled face of one of the back body blocks, then mount that assembly in a vise.

Clamp the front and back body blocks to one of the cheeks using a straight board to align the parts accurately.

Add the opposite cheek, then temporarily clamp the parts and bore pilot holes in the end waste areas for screws. Install the screws and remove the clamps. Repeat the procedure for each plane. Remove the screws and set the parts aside while you prepare the crosspins.

Wrap the faces of each blank with masking tape so that your layout marks will be easily visible, then mark the shoulders of each tenon. Install the parts of a wooden hand plane kit cutter in the drill press, then clamp a tall fence and stopblock to the drill press table. Clamp one of the pin blanks to the stopblock, and check that it is perfectly centered under the drill chuck. Install the plug cutter in the drill and use it to cut the tenon.

Stop the cutter just before it reaches the shoulder kerf, then remove the blank and use a sharp chisel to clean up the shoulder. Repeat the process for each tenon. Check the fit of each tenon in a test hole drilled in a piece of scrap lumber. If the tenons are too tight, use grit sandpaper to adjust them until they slide easily into the hole. It is important that the tenons are snug, but the pins need to be able to rotate to adjust properly to the angle of the wedge.

Use a rasp, file and sandpaper to round the top pin surfaces as shown in the plans. Prepare one of the plane bodies for glue-up. Next, apply glue to one face of each of the body blocks and place them on the cheek. Position parts of a wooden hand plane kit crosspin in the opposite cheek and spread glue on the remaining surfaces.

Assemble the parts and drive the screws to ensure that the parts are aligned. Clamp the assembly, and allow the glue to set for at least an hour before removing the clamps and scraping off excess glue. Repeat the assembly process for each plane. Use a band saw to cut off the waste portion at the ends of each block. Transfer the side profile of each plane to its blank and cut out the shape.

Mount one of the plane bodies in a clamp and use a rasp to shape the back-end profile. Keep in mind that the plane should be comfortable in your hand, so test its feel as you shape it.

Now is the opportunity to personalize your tool. Finish shaping the back using a file and sandpaper. Then chamfer the top and front parts of a wooden hand plane kit, and sand all outer surfaces withand grit sandpaper.

For a plane to be useful as a flattening and straightening tool, it is essential that the sole be perfectly flat. If your assembly has gone smoothly, your tool is probably pretty close to being flat, but it still needs some work. The easiest way to flatten the sole is to stick a strip of self-adhesive sandpaper to the table saw table and repeatedly pass the plane over it.

Apply pressure only on the forward stroke, then lift the tool to bring it back for the next stroke. Examine the sole of the plane frequently as you work. You will be able to see if there are areas that still need work. Use a sanding block to ease the corners around the sole, then repeat the process with and grit to polish the sole.

Rip a strip of wenge to width for one of the plane wedges, place a piece of masking tape on one edge and lay out the wedge shape. Then cut the inside surface of the wedge. Slide the iron and cap-iron assembly into parts of a wooden hand plane kit plane and test the fit of the wedge. Use grit sandpaper to adjust the shape of the wedge, as necessary, so that it exerts even pressure across its entire width. You will know when the fit is correct when you see an evenly burnished line across the wedge face at the point where it contacts the crosspin.

Then, use the band saw to finish cutting the back and top profiles of the wedge, and smooth the cut surfaces. To seal the wood we applied a penetrating finish of several coats of boiled linseed oil. Use a rag to completely soak all surfaces of the plane and wedge, let the oil absorb for about a half-hour and then wipe off the excess. After overnight drying, repeat the process. Apply at least three coats using this technique.

You can then apply a light coat of wax to the sole of the plane to further reduce friction. Slide an iron assembly into one of the planes so that the cutting edge is flush and parallel to the sole, then position the wedge and give it a light tap to lock the iron in place.

To parts of a wooden hand plane kit the parts of a wooden hand plane kit of cut, use a small hammer to tap the iron lightly. To decrease the depth of cut, use a wooden mallet to tap the back end of the plane.

After each adjustment, you should check the tension on the wedge, as it may need tightening. Type keyword s to search. Today's Top Stories. Or Even Holes. The 71 Best Tools of This content is created and maintained by a third party, Parts Of A Wooden Hand Plane Names and imported onto this page to help users provide their email addresses. You may be able to find more information parts of a wooden hand plane kit this and similar content at piano.

Advertisement - Continue Reading Below. More From Projects and Plans.

Hand planes are the living link between woodworking hands and the wood they work on, bonding the craftsman to the craft. Hand planing wood, working with a fine hand plane is one of the most pleasant of all woodworking tasks. This is Ron Hocks small version of his ever-popular Krenov-style wooden plane kit This handy Block Plane comes with a 1 in. wide blade, ends up 5 3/4 in. long and trims down to 5 in or less depending on your needs The plane in the photo is just 3 1/2 in. long -- a very convenient size for an apron www.- s: Hand Planes at Carbatec - The Home of Woodworking. Shop online, Click & Collect or get it delivered. PayPal & ZipMoney available.

Door Pivot Hinges Uk Key Soft Close Drawer Slides Stiff Key Router Table Saw Extension Youtube Woodworking Jig