%!$ Easy Diy Woodworking Bench Plans For You #!@

makita-2711-miter-gauge-pdf The use of improper accessories may cause risk of injury t o persons. Page 30 Saw blades Chisel tooth combination saw blade rip and cross-cut work. Continue Shopping. In Stock, 13 available. Use your left hand to hold the workpiece in position against the rip fence.

This diagram has more than one page. Please click the images below to load the different pages. Page: 1 2. Items 1 to of total Show per page.

Bolt Checkout. Screw M5X65, Ga Screw M5X65 for the Ga Screw M5X40, Screw M5X40 for the Washer 18, Lxwt Washer 18, Lxwt01 - Makita Part number is a F. Washer 18 for the Lxwt Bearing Lb, Ga Bearing Lb for the Ga Screw M4X10, Fct. Screw M4X10 for the Fct. Screw M4X14, Screw M4X14 for the Screw M5X30, Screw M5X30 for the Bearing , Bearing , - Makita Part number is a N.

Bearing for the Spring 14, Spring 14, - Makita Part number is a Ten. Spring 14 for the Add to Cart. Lever 90 CPL. Page B. Miscellaneous Parts. Popular Parts. Carbon Brush Set. Cord Guard. Lock Button. Ball Bearing. Pan Head Screw. Rubber Pin.

Power Cord - 8', 16 Gauge, 3-Wire. Table Saw Parts Saw Parts. Repair Guides Power Tool Care and Maintenance This article suggests guidelines for power tool care and maintenance. Accessories for the Makita TCT Saw Blade.

Blade 36T. See more Standard Saw Blades. No questions have been asked yet. Ask a question. Previous Page. Next Page. Makita portable band saw instruction manual f 25 pages. Read the owner's manual carefully. Learn the tools applications and limitations, as well as the specific potential hazards peculiar t o it.

Page 3 The use of improper accessories may cause risk of injury t o persons. Serious injury could occur if the tool is tipped or if the cutting tool is accidentally contacted.

This tool is equipped w i t h an electric cord hav- ing an equipment-grounding conductor and a grounding plug. Page 5: Additional Makita 2711 Miter Gauge Jack Safety Rules Never wear gloves during operation. Keep hands out of the line of saw blade. Do not stand or permit anyone else t o stand in line w i t h the path of the saw blade.

Make sure the blade is n o t contacting the spreader or workpiece before the switch is turned on. Page 6 jam the blade in the workpiece, turn the tool off immediately. Unplug the tool. Then clear the jam. Never remove cut-off pieces near the blade or touch the blade guard while the blade is running.

Don't abuse cord. Never yank cord t o disconnect from receptacle. Page 8 Loosen the wing bolt securing the sliding table before mov- ing the sliding table.

Installing or removing saw blade Hold the outer flange with the offset wrench and loosen the hex nut clockwise with the wrench the hex nut has left hand thread. Page 9 Install the blade between the two flanges. Then install outer flange and hex nut onto the arbor, making sure the teeth of Makita 2711 Miter Gauge Filter the blade are pointing down of the table. To secure the blade in place, hold the outer flange with the offset wrench, then tighten the hex nut counterclockwise with the wrench. Page 10 Installing and adjusting rip fence Loosen the lever on the rip fence and f i t the rip fence on the ruler guides.

Page 11 Tighen the lever on the rip fence. I f the rip is not fence secure enough, in the tightened position and tighen the screw in the hole in the rear end fence clockwise. However, do not tighten the screw excessively, or the lever will be- come loose.

Maple Wood Veneer 400 Veritas Shoulder Plane Blade Version