%!$ Easy Diy Woodworking Bench Plans For You #!@

drying-green-wood-for-turning-water They are 3 inch thick and kiln dried aggressively for 3 weeks. Awareness aood the changes that take place once the green wood is turned is the key. Repeat the process weighing the wood bowl after each session until the weight of the bowl stabilizes. There is a bunch of information for plankers out there wlod not much for bowlers. Knowledge is addictive and I continue to be thankful that you share yours in such an informative fashion. Members Registered members Current visitors. Well, as you guessed there are many drying green wood for turning water to take into account to determine how long a piece will dry or equalize.

The surfactant makes water "wetter," but any gain is pretty well taken care of by reduced capillary draw. Ethanol, with its lower boiling point is alleged to make water evaporate faster, but that would seem to defy the process by which we get alcohol - distillation. They have not repealed Raoult's law, that I know of. An inch thick in end grain shouldn't take more than a couple months to stabilize with the ambient relative humidity. Slow evaporation with a coating or covering, add a bit more time.

Push it by putting the piece in fairly low humidity, subtract time but increase chances of checks. I soak the bowls for 4 days then set out to dry for 3 weeks.

I have tried it with maple, cherry, elm and ash with no cracked bowls yet. I have only tried this on 8 bowls, not enough to say it works or doesn't. We'll see what happens to the finished pieces over the next month.

So far a week after being finished the completed bowls are still round and look great. I do not plan on continuing to do this since I have been turning a year now and have plenty of rough outs waiting to be finished. A new turner talked me into trying it with him. Good Luck Matt. Jack Savona. The process I now use almost exclusively is the LDD.

Don't know how it works, but I can say that within weeks my roughouts stabilize their weight and show minimum distortion and generally no cracks. I have successfully tried cherry, hickory, walnut, maple, poplar, birch, elm, and with some challenge oak.

I even use it for my natural edge bowls and bottle stopper blanks. I know the popular method these days appears to be Drying Green Wood For Turning Quarter DNA, but its cost and safety issues have concerned me. I use the cheapest dollar store or Drying Green Wood For Turning Radius supermarket soap and keep a little squirt bottle with white vinegar nearby to neutralize the alkaline feel of the soap on my hands.

Steve Worcester Admin Emeritus. Dustpan said:. Click to expand Jeff Jilg. Bill Boehme Administrator Staff member. Beta Tester. The dishwashing detergent method not a soap although most people don't know the difference is NOT to reduce the drying time most woodturners think that it is , but to stabilize the wood by replacing some of the water with a never drying concoction of glycerol, perfume, FDA Green??

MW, and who know what else. Soaking in PEG does roughly the same thing and neither one speeds up the drying process. On the contrary, the wood may never get as dry as a conventionally dried piece of wood. However , both of these methods, which are intended to be used only on freshly cut green wood after rough turning , do allow you to turn something without waiting for it to completely dry -- so it does reduce the waiting time before you can turn it. Despite the glowing testimonials on both of those methods, I'll stick with the old fashioned way of doing it.

I have some misgivings about the long-term effects on the wood and on finishes applied over detergent or PEG. Max, I have a 10 lb. Last edited: Mar 29, Andy Coates. I've used it on spalted beech with great results. A three day soak and a three day drip dry As others have mentioned this process seems to "fill up" some of the flacid cells which have collapsed through the spalt and allows the wood to be turned fairly well.

It's my belief that any assumed success when this process is used to dry wood is simply good luck. In the summer of I turned a series of large bowls, " dia. These were turned to finished dimensions and have since shown Storing Green Wood For Turning 2020 no distortion whatsoever. Just good luck. And, I should add, these bowls received no treatment whatsoever. We are planning to store in the garage for even drying and keeping as flat as possible. My concern is am I attracting termites by doing so? We will remove all bark prior to stacking and storing.

Any suggestions would be welcome. We are using Queensland cypress for our gates. We have trouble with weight over 8 foot long hanging from hinges and gudgeons as our glue seems to be failing. Can you recommend an extremely strong glue for this purpose. Our timber comes from our local sawmill so it does seem a little wet and heavy whilst working with it, maybe this is the problem? We have rails and bracing and now having to screw at the stiles for added support.

Resorcinol resin is 2-part glue often used by shipwrights for waterproof permanent bond. Requires tight fit and strong clamping. I am making signs with live edges. These are rough sawn pieces. Thank you. Only thing really heat would be needed for is to kill insects or other pests, but in terms of drying, should be sufficient. Question is alright to move white oak inside after siting Outside for a year? It has cupped a bit.

Making stuff with recently fallen trees. Red Cedar, Black Walnut. Any info or advice on using dehumidification equipment to dry out chainsaw milled lumber. Hello — just wondering if you received an answer to your question? Any information you have would be appreciated.

Thanks, John. Lots more details to learn. I have a Holly tree that has a 24 inch circumference and an almost clear trunk of 6 feet high.

It needs to come down as it is too close to the house. I would like to make a solid body electric guitar out of it. What thickness planks would I need to start with if the finished product is to be 1. Length x Width of body: Hi, came across your question. Twists and pockets forming around knots is common with holly. The grain of holly is nothing … Read more ».

Thanks Ian, I expect to do just that, strips instead of planks in about 3 years time. Thanks for the drying info. Well , I have cut it down and milled it into 5 foot, 2 usable 2. I have a concrete room I can seal off with plastic on one side. Will then cut and seal the ends.

Sticker and stack with 1 dehumidifier and 2 box fans to move air. I am getting a pin type humidity probe and wireless temperature and humidity sensor. We are in … Read more ». Hello, I inherited a garage full of miscellaneous wood from a fellow who had a custom furniture shop. There are a lot of ash strips that he used for the edges of plywood shelves.

Using the data you present for wood species, how do I determine if a particular wood is open grained and unsuitable for cutting boards?

The benchmark cutting board wood … Read more ». But really the best metric for finding suitability is found in pore size. Maple has pores that are just small enough to cause them to become plugged up with sawdust during the building phase. So when a finish is applied, the surface of the wood seems smooth it is smooth, but only because the small pores have been jammed with sawdust.

With woods like ash, oak, … Read more ». We asked to keep some pieces for future furniture project-Tree stump side tables. Please advice to treat humidity, drying, and stacking.

Much of what I see on-line are air-drying directions for traditionally-sized boards in order to use the walnut for fine furniture. For what I need—just a rectangle hanging on the wall—how short an air-dry time can I get away with? Are you going to do a more refined finish, like a glossy, pore filled finish? Or are you going for a more rustic or rough-sawn look? Thanks Eric. Very helpful. In the sun? Definitely keep it out of the sun. I just cut a lot of cherry. I very rough cut the logs with my chainsaw.

Thickness is very uneven throughout the boards, and frankly, some have bulges and some are wedge shaped. Should I plane the boards for uniform thickness before stacking? Yes definitely. When you stack on stickers and have a lot of variance in thickness. Leaves room for movement and warping. Green would does not like to feed in a planer.

Might have to live the bed with wd Thought I read somewhere that wood stickers should be of same species as wood being dried …. How much shrinkage should I expect? Length does not shrink near as much. But most species would take years to dry that size. I would wait 1 year and hope for the best. I love in Oregon.

They cut down my grandfathers old oak tree on Friday. They delivered five slabs cut from the trunk. They are approximately five feet in diameter and approximately six inches deep. Too heavy to move them. We did stack them on wood to get them off the asphalt and between layers. How do I process these? I am interested in using the wood for projects nothing specific yet. Get it cut, seal the cut ends, slab it with a chainsaw or split it into whatever size is manageable, raise it off the ground, and get it stacked and stickered in a windy, shaded spot with some kind of cover over the top.

In Iran and the region Mulberry is exclusively saved and used to build string musical instruments: Taar, Setaar and Tanbur Tambur. I found that while sanding then applying topcoat there is a faint line where the sticker was.

I had to sand off finish and sand deeper than desired. Any ideas on an alternative choice of sticker material? The stack is dead flat. Im new to this all. Or should I just give it a shot and see what happens. Also, should I dry these babies out before putting on legs? Here are some pictures. The arborist told me different … Read more ». These are sections and will dry with high stress.

After time, say 6 months to a year, the wood will suddenly split from the edge to the center in one place, leaving what looks like a wedge defect. This is due to the circumrferential shrinkage tangential being greater than the radial shrinkage. There are two fixes. You can saw the blank in half, then dry it down, then resaw the two pieces which will develop a convex angle of a degree or two along the cut surface.

Alternatively, a chemical treatment to keep moisture in the wood can be used. Steve thank you. Maybe I need to wipe off the wax and let the sun do its job. Any suggestions? I would keep it out of the weather, the sun will just bleach it. Put it in your garage or somewhere dry and put a fan on it to help discourage any more mold growth. Pour denatured alcohol onto the surface of the pieces and let it flow trough to the bottom side. Wood is like a million tiny straws when cut into discs, this will force the moisture out.

If you have a pan big enough you can catch the alcohol as it comes through an reuse. I made about oak disks out of green wood and used this method I only had 1 crack. Sounds like that worked fantastic with those! I have someone offering for sale some raw never stained or varnished hardwood flooring that has been stored in his garage for years 10 plus.

He says some is cherry and some is black walnut. He got it from a flooring company that went out of business. My cabinet maker told me to stay away from it as it will likely be too high in moisture and will distort after installing it on my floor. I live in London,Ontario Canada. High humidity. What is your opinion.

If it has truly been stored for 10 years, it should be dry. Also a good idea, if you do end up getting them, to let them acclimate to your humidity level indoors for a while in the same location where they will be installed.

Best time to do all this is in a drier time of year such as fall. How long does the powder post beetle larvae live in air dried wood that is about 3 inches thick, 2 feet wide Drying Green Wood For Turning 05 and 4 feet long, the wood is sycamore. I will be air drying a disc of white ash recently cut. It is 3 feet in diameter and at least a foot thick. That is, cut right across the trunk of a huge tree killed by Emerald Ash Borer. Here, only White Ash could be that big. I bought a square metal outdoor fireplace box to use as a drying stand.

I can shade it with an old table-tennis table I use outdoors. Will this work? I just had a bunch of hickory sawn down into 2. They are in a uninsulated garage with a fan moving some air. The problem that I am having are the slabs are starting to spilt at ends. I never painted or sealed ends. If I cut and seal ends will this help? Do I turn off fan to let them just dry slower?

I would both cut and seal the ends and turn off the fan. Hello I want to cut oak trees northern California and use the tree trunk together with the bark to build a bed frame. Any suggestions how to dry the wood to keep the bark on and prevent mould? Thanks for any recommendation. Great ambition to leave the bark on the wood, but that adds exponential difficulties to your finished product.

Bark on looks great for synthetic wood-looking displays at restaurants and outdoor living stores, but my advice is to keep away from leaving the bark on. I have roughly 1. Hoping to preserve the bark, and prevent cracking as much as possible. Some have frozen sections Canadian winters are fun. Would you suggest soaking in pentacryl once thawed out , stacking and drying, or just painting it on almost like poly throughout the drying process?

I have imported Peruvian walnut slabs from Honduras. They are 3 inch thick and kiln dried aggressively for 3 weeks. A very short time, I know. Unwisely, I had relied on local expertise. Once shipped and delivered and after checking a small sample, the MC inside was much higher and checking was visible. What are my options? Is there any comeback? Should I just leave them out to continue drying or should I find a kiln that can properly finish the job or is it now firewood?

In the future I think I … Read more ». Hey Larry, I live in Honduras. This is really beautiful stuff—I like it even more than american black walnut. Regarding the pile that you have, you might want to cut a foot or two of the ends and dry it all as slowly as you can, though in all honesty, this is a very stable wood.

All the best … Read more ». I had a small tornado hit my place and knocked down alot of trees cedar, oak,hickory ,walnut ect i want to mill the cedar into 1 inch boards and Shiplap side my house I have a big shop area with a wood stove In it my question is how long will it take the cedar to dry and what is the optimal temp to keep the shop while drying?? That is one reason for high use of cedar shakes rather than timbers. If you can be flexible regarding exposure of each siding piece, then you can easily overlap each cedar piece according to its natural curves and your aesthetic will be a rustic, great look to it!

The poles will not support anything, just brace the outer wall from movement when the patio door is closed and add aesthetic value to the open area. The trees will remain intact with the bark. How do I dry these birch poles to ensure they do not rot and the bark stays put?

I have a question… My husband has been drying out wood for a few years and I am trying to have a wall created similar to shiplack but not tight or finished just propped that way on the wall for storage purposes.

Will it damage the wood at all to put it on it side like this? It will still get air. It will just be stored on its thin side and not wide side. Does this make sense? Great article — I have a question. I cut some rounds and some 45 degree slabs from a black cherry to make cutting boards. Do you think i can apply salad bowl finish right away to reduce any cracking and splitting?

I was wondering if applying the finish would displace the moisture and then i could sand them down when a bit drier. Did you find a solution to this? Did u ever get an answer to ur question about ur blk. I am remodeling my house and bought red oak retreads for my steps and they are 1 inch thick. I double coated the topside not the underside with polyurethane and left them in the garage about3 weeks.

Unfortunately the all occurred during prolonged periods of rain and they cupped upward. The installer cannot use them. I am looking to salvage the retreads if at all possible. Can I use a kiln to dry out the retreads and will they straighten out? Is there any advice that anyone can offer to help me out of this expensive error.

I was … Read more ».

Long Woodworking Square Ltd Electric Belt And Disc Sander 2020