%!$ Easy Diy Woodworking Bench Plans For You #!@

drawer-lock-router-bit-setup-80 For flush-mount drawers, or drawers to which you'll biit a false front, place the fence only the thickness of the drawer side from the bit's lower cutting setul. Rail and Stile Shaper Cutters. In these photos I am making a test cuts on scrap wood, which is an identical thickness to my drawer pieces. I hope you found something useful in this article! Become A Member. Next time you need to make the cuts again drawer lock router bit setup 80 same-sized material you can re-set the bit and fence until it fits perfectly into your saved reference cut.

This is of course a tricky setting, so you will definitely need to have some scrap wood available for making test cuts. In these photos I am making a test cuts on scrap wood, which is an identical thickness to my drawer pieces. The two cut pieces then fit together like this final photo locking together. This is my fourth test piece. So I had to adjust the fence four times to get a nice flush fitting joint. Considering how rudimentary my fence is, I think that is pretty good. If you try this, just remember to have several pieces of scrap available for test cuts -- or just one long scrap piece, which you just keep cutting down shorter.

With the router table properly set up, I proceeded with batch cutting all of the drawer pieces. In order to keep things from getting messed up, I first lay out and cut all the drawer fronts and backs You need to be careful with the sides, to hold them perfectly perpendicular with the end flat on the table as you cut them.

I had a few mistakes where the piece tilted a bit as I pushed through the cut, and I had to re-do those pieces. I then moved on and cut rabbets along the bottom of the drawers, to h hold the bottoms. I cut the back of the drawer shorter, so that the bottom can slide in and out. I also cut out the bottoms. None of that was filmed, as the focus of this article was just on the joinery. With the drawer pieces ready, it is now just a matter of adding glue to the ends and then alinging and clamping the pieces.

I slid in the plywood bottoms immediately, as they help with ensuring that the drawer box is square. Here is one shot showing a nice tight drawer corner joint. The two drawer pieces lock together securely, and the joint is closed and flush. In the interests of full honesty, here is also a photo of one of my Don't fumble with router bit setup, some cutters take more time to get setup correctly. Made from pre-cut high density plastic, they'll make once frustrating bit set-up a thing of the past.

Don't waste wood or time. Router Bit Setup Blocks. Item SETG. Skip to the end of the images gallery. Skip to the beginning of the images gallery. Add to Cart. In stock. Pre-Machined Router Bit Setup Blocks Don't fumble with router bit setup, some cutters take more time to get setup correctly.

Checkout the helpful videos for set-block usage below. Bit height is especially critical. Start by using the techniques we provide for getting it close. When making drawers one of the cuts will be across the face grain. This can lead to a lot of tear out and chipping on the face. Drawer locks can also be created on the table saw using a dado head. This is another great way to create lock joints.

You should also check out our content on different types of joinery. For more information on Kreg products visit www.

Click here to cancel reply. Hi Curtis. I believe that you can use it on any thickness by making the proper adjustments to your router table fence, but Whiteside suggests other bits in their product line for thicker stock. I think it would be really hard for me to cut into the fence for zero clearance.

I paid a lot of money for my Jessem fence. This would mean my fence would be cut for a specific thickness of stock. You can always take the stock fence off and replace it, temporarily, with an MDF or melamine shop-made face. This was very useful. Thank you! Hi Dennis. The step where you cut into the fence is to create zero clearance around it.

You can use a sacrificial fence for this. A backer board can be used behind the piece as you push it through the cut, which will reduce the chance for blow-out on the trailing edge of the cut. I would 1st start with a sacrificial fence mounted and then make my adjustments. I would never purposely cut into my Kreg fence! That really surprised me! While your on the subject demonstrate the lock miter bit which is even more fidgety to dial in, accordingly highly recommend using a router lift with a bit height locking feature.

Hi Christopher. It is mounted on a shop-made cabinet that George built. I was using my Leigh RTJ They did not recommend using plywood.

Hardwood Products Co Maine Jewelry Soft Close Drawer Slides Not Working Utility Tape Measure Digital Bosch Water Is Salad Bowl Finish Waterproof Us