%!$ Easy Diy Woodworking Bench Plans For You #!@

danish-oil-cherry-quote At this point you want to remove cherdy excess with a clean rag. The first step to obtaining a good finish is to smooth the surface well, prior to applying the Danish oil finish. I wanted to follow up with the final results. Tpt life Posted August 30, Indy Cindy Posted August 30, Danish oil cherry quote love the natural, light wood — it is Birch.

I sanded with 80, , , , , , I then applied 3 coats of each finish according to Watco's directions. At first they did not look that different other than the sun exposure but then I zoomed in. Here is a closeup of the Watco Danish Oil in Natural finish:. The cherry finish really brought out the finer grain and gave the wood a redder tint.

I also really like how the sun exposure gave the wood a brown tone. I think I would be happy with any of these choices but I may try to expose the entire piece to the sun and use the Cherry finish to bring out those fine bits of wood grain.

Now I need to build myself a rotisserie to make sure the finished piece is fully exposed to the sun. I am currently testing some cherry as well. I used some iron acetate on a piece, and within 15 minutes it was a little darker than you sun-exposed piece.

I used a thin coat of amber shellac to make it redder, but I like how your Danish Oil turned out. The "cherry" sample looks blotchy. Controlling the blotch might alter the hue slightly. I would test with that control as part of your test. Before I was a woodworker I hated 'cherry' wood because little did I know that it was really cherry colored some-other-wood.

It was red and overbearing and looked fake. It takes time for the color to Danish Oil On Walnut Plywood fully develop. Here are a couple pictures of a table I made in , finished with Arm-R-Seal natural. The first picture was then, the second is now. This table lives in a different room than where I took the pictures and gets no direct sunlight, I imagine the color change would happen quicker in a brighter room.

When I first finished the table I thought it looked bland but was told the color would become richer and darker. It's amazing what a few hours in the bright midday sun will do to get the color darker on a brand new piece. Or a tanning bed if the piece will fit.

I Googled it and saw this article. Looks interesting but I like the simplicity of a oil finish. I'll file that away to try another time, Thanks! C Shaffer I'm not sure where the blotching is, but then I don't notice when my wife gets her hair done either and I get into trouble.

I'll have to develop an eye for that. Seemed to work well but I'm not sure I have an eye for seeing it as well as others. Indy Cindy Beautiful table! Very noticeable how it has darkened, well done. Thank you for all the great feedback, I just finished my second prototype this weekend upper left in photo in pine Watco Natural Danish Oil. This time I cut the pieces so the grain would flow from piece to piece.

I also like the way the end grain ran along the edge front compared to the first prototype back. I wanted to follow up with the final results. I ended up using Watco Danish Oil in natural on the final build using Cherry wood. After sanding I put the piece out in the sun for about 15 hours, turning it every few hours to even out the exposure.

I really like the final results and more importantly my wife likes it. Thank you, I believe that the sun exposure made a big difference so going with Natural was an easy choice. Yes, after 80 grit it was hand sanding all the way to I have two cherry midcentury tables my dad made in the 60s.

They need refinishing and I was undecided about what finish to use. You guys sold me Danish Oil Finish On Walnut 2019 on the Danish natural. They have aged beautifully and it should show the color nicely. You can post now and register later. If you have an account, sign in now to post with your account. Paste as plain text instead. Only 75 emoji are allowed. Display as a link instead. Clear editor. Upload or insert images from URL. Cherry Danish Oil on Cherry?

Reply to this topic Start new topic. Recommended Posts. Cubist Woodworker 1 Posted August 4, Posted August 4, Link to post Share on other sites. IMO cherry shines with a natural finish. If you want to color cherry then just use maple. Wdwerker, I didn't know that about cherry, I'll give it a try, good advice! Thanks guys! Gilgaron 94 Posted August 4, Cubist Woodworker 1 Posted August 5, Posted August 5, Cubist Woodworker 1 Posted August 30, Posted August 30, edited.

Both these oil are wood finishing oil, but both oil function in different manners. Tung oil is a component used to make Danish oil. However, the addition of other materials makes Danish oil different in nature from tung oil.

Now, this article is aimed at helping you to decide which oil you want to use to finish your woodwork. Danish oil is basically a mixture of various components such as tung oil or linseed oil, as well as a mixture of varnish, mineral Watco Danish Oil Application Website spirits, etc.

There is no fixed formula of Danish oil, and so it varies according to the manufacturer. Now, Danish oil is usually applied over a bare surface of wood in the direction of the grain for better results. It penetrates the wood easily and dries faster due to its mixture of various components. This oil is ideal for beginners, as its application is quite easy.

It will protect your woodwork from scratches, damages done by chemical or heat, stains, etc. Unlike other oils, Danish oil does not become yellow with age. If you have a particular shade in mind, you can simply mix various tints to get your desired shade, and then you can also use it as a primer or sealer. It is water-resistant and is durable as well. It is perfect for you if you are a beginner or novice woodworker as you can just apply it on the bare surface of the wood without any hassle.

As Danish oil is diluted with other components, it does not take days or weeks to cure. And it needs fewer coats and curing time as well.

Water damages can ruin all your hard work, so make sure to pick up Danish oil that will leave a waterproof coating on your furniture.

It seeps into the wood faster than other oils such as Tung oil and so can be used on hardwoods such as cherry, oak, maple, ironwood, and mahogany. It is very difficult to know what chemical compounds are present in Danish oil. So it may be hazardous for health if it is used to make materials in which food is stored. One advantage of Danish oil is that it hardens as it comes into contact with air if it consists of polymerized linseed oil.

However, there is also a possibility of spontaneous combustion due to exothermic combustion. So to avoid any danger, be careful and make sure to either let the rag used to apply Danish oil is placed flat to dry out or soaked thoroughly in water before discarding it.

Tung oil has been in use for centuries; it was used by Chinese in building ships and was also mentioned by Confucius in about BC in his writings. It is derived from nuts from tung trees that are indigenous to China, and so is also known as China wood oil.

As it is organic and all-natural, tung oil does not have any toxic elements. Tung oil provides the best waterproof coating amongst all oil treatments. It also provides a beautiful golden color to wood. Amongst all other oil treatments available, Tung oil is the only on that polymerizes hardens completely and does not darken as it ages and Watco Danish Oil Regina is less vulnerable to molds.

It is known for being waterproof and has been used for hundreds of years for its ability to make wood waterproof. Once it is properly applied and cured, your furniture will be safe from absorbing water.

Tung oil hardens completely, but it also remains wonderfully elastic, and so contraction or expansion of wood does not affect the coating. Furthermore, it prevents cracking on the surface and increases the lifespan of the wood.

As Tung oil polymerizes completely after it is cured, it leaves behind a very hard coating on the surface of the wood, and so keeps it safe from scratches, acidic components, dents, etc.

Tung oil is safe to be used in making kitchen utensils as it is an all-natural and non-toxic product.

Miter Saw Digital Tape Measure Model Woodpecker Tools For Sale Virus Lumber Products Examples 60