%!$ Easy Diy Woodworking Bench Plans For You #!@

belt-disc-sanders-woodworking-network Belt-Disc Belt And Disc Sander Harbor Freight Network Sanders

Model No. Put it and the original sales invoice in a safe, dry place for future reference. Single 2 Belt size Sanding of steel or other ferrous materials is a fire hazard and could damage your sander. WARNING Some dust created by power sanding, sawing, grinding, drilling and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area and work with approved safety equipment. WARNING Always follow proper operating procedures as defined in this manual even if you are familiar with use of this or similar tools.

Remember that being careless for even a fraction of a second can result in severe personal injury. Do not wear loose clothing gloves, neckties, rings, bracelets or other jewelry which may get caught in moving parts of the tool. Everyday glasses have only impact resistant lenses. They are NOT safety glasses. Never operate power tools when tired, intoxicated or when taking medications that cause drowsiness.

Cluttered work areas invite accidents. Do not use belt disc sanders woodworking network tools in damp or wet locations.

Do not expose power tools to rain. Three-prong plug should be plugged directly into properly grounded, three-prong receptacle. Ensure your work shop is child-proof. Use padlocks, master switches or remove switch keys to prevent any unintentional use o power tools. Form habit of checking to see adjusting tools or accessories are removed before switching tool on. Check to determine that guard or other parts will operate properly and perform their intended function.

Do not perform makeshift repairs. Do not force your tool or attachment to do a job for which it was not designed. It will work most efficiently at the rate for which it was designed. Keep hands away from moving parts and sanding surfaces. Turn the power off and do not leave tool until it comes to a complete stop. Keep proper footing and balance. Serious injury could occur if tool is tipped or if sanding surface is unintentionally contacted.

Use of improper accessories may cause risk of injury to persons. Protect hands from possible injury. The motor may jam if too much pressure is applied on the sanding surface. Safety is a combination belt disc sanders woodworking network operator common sense and alertness at all times when tool is being used.

Check for shipping damage. Check immediately whether all parts and accessories are included. If anything is missing, or broken, contact your retailer or call Figure 1 The sander comes assembled as one unit.

Additional parts which need to be fastened to sander, should be located and accounted for before assembling. Call the Customer service line to obtain replacement parts. Do not operate this tool until you have completely read and understood this manual.

Choose a suitable location to mount the sander. The sander belt disc sanders woodworking network be installed in a place with ample lighting and correct power belt disc sanders woodworking network. To install sander: 2. The sander must be bolted to a firm, level surface. Make belt disc sanders woodworking network there is plenty of room for moving the workpiece. There must be enough room that neither operators nor bystanders will have to stand in line with the wood while using the tool.

Allow room so that the belt assembly can belt disc sanders woodworking network positioned horizontally. Sander can be installed on a workbench or tool stand using belt disc sanders woodworking network, lock washers and hex nuts not supplied. Insert support rod 1 into bracket 2. Secure with bolt 3 on flat surface of rod. Position table assembly 4 on rod. Secure with bolt 5 3.

Using a combination square, set the table perpendicular to the belt and secure in position with knob 6. If necessary, set pointer 7 at 0.

Belt disc sanders woodworking network disc cover 1 by loosening and removing five screws 2. Peel protective paper from the back of the abrasive disc 3 3. Center the abrasive disc onto the aluminum disc and press on firmly and evenly.

Replace disc cover. To use the table with the disc: Fig. Insert support rod 1 into base 2. Secure with bolt 5. Using a combination square 6set the table perpendicular to the disc, and secure in position with knob 7. If necessary, set pointer 8 at 0. Place clamp 1 over bag sleeve 2. Slide sleeve with clamp over the dust port. Secure in position by tightening clamp handle.

Do not force handle. Rotate the handle to increase the clamp size. Running the unit on voltages which are not within the range may cause overheating and motor burn-out.

Heavy loads require that the voltage at motor terminals be no less than the voltage specified on nameplate. Remove the key to prevent unauthorized use. Equipment should be grounded while in use to protect operator from electrical shock. In the event of a malfunction or breakdown, grounding provides a path of least resistance for electrical shock.

Extension Cord Length Wire Size……………. The electrical wiring schematic is shown in Figure 9. The permanently split capacitor motor has the following specifications: Horsepower Peak HP. Single RPM. Make sure tool is off and disconnected from power source while motor is mounted, connected, reconnected or anytime wiring is inspected.

Motor and wires are installed as shown in wiring schematic See Figure 7. Motor is assembled with approved, belt disc sanders woodworking network cord to be used at volts. Do not modify plug provided.

If it will not fit in outlet, have proper outlet installed by a qualified electrician. If repair or replacement of the electric cord or plug is necessary, do not connect the green or green and yellow wire to a live terminal.

Motor Power Cord The power lines are inserted directly onto the switch. The green ground line must remain securely fastened to the frame to properly protect against electrical shock. The power supply to the motor is controlled by a single pole locking rocker switch. To turn the sander ON insert the yellow key 1 into the key slot in the center of the switch. Push the key firmly into the slot, then belt disc sanders woodworking network switch to the ON position to start the sander.

To turn the sander OFF push the switch to the down position. Remove the yellow switch key, when the sander has come to a complete stop, by gently pulling it outward. Place it in a safe place and out of reach of children. Remove the key and keep it in a safe place. In the event of power failure, blown fuse, or tripped circuit breaker, turn the switch OFF and remove the key, preventing accidental startup when power comes on.

Figure 8 1 Fig. Loosen socket head bolt that is threaded into pivot bracket. Tilt belt assembly to desired position. Secure belt assembly position Ryobi Belt And Disc Sander Parts Shop belt disc sanders woodworking network tightening socket head bolt in pivot bracket. Adjustable positive stops are provided for both horizon tal and vertical positions. NOTE: The horizontal limit stop is located on top of the base. Make sure tension lever belt disc sanders woodworking network is tight toward drive drum.

Dec 24, Belt And Disc Sander Toolstation Network  · A power disc sander moves this list of best wood sanders into the specialty sanders. For intricate or small sanding tasks a disc sander provides precise control as you hold the wood, not the sander. If your projects have a number of small pieces or you need to precisely sand the end grain of small sticks then this is a sander for you.

Build A Toy Car Garage Zip Code Wood Whisperer Parallel Clamps Limited Stainless Steel Non Mortise Hinges