%!$ Easy Diy Woodworking Bench Plans For You #!@

100-percent-tung-oil-45 All rights reserved. Be the first to review this product. Young and Thomas J. It's your call. We were very unhappy with the wear of okl wood floors and poly in past homes.

Oh and those recessed floor registers. Thanks, Katja! The floor registers are definitely one of my favorite parts — and it makes cleaning even easier. Lazy girl over here. The floors look really nice, I love natural oil finishes! I am completely heart-eyes for those custom registers, what a lovely little detail!! Kim you have done such a justice to your home, great choice. Thank you, thank you, thank you for installing real wood floors.

I get so tired of seeing prefinished, partly laminate, click and snap crap all the time. Our year old wood 100 Percent Tung Oil Zip floors are only oiled as well, no poly or stain, the beauty and natural wear are what makes wood floors amazing.

Way better than adding chemicals and off-gassing to your beautiful new home. What a great choice! Thanks for the floor loving shout out friend! This is such a helpful, inspiring post!

Just a year later, the natural color variations are more pronounced and get prettier everyday literally. Go team tung oil!!! Thank you so much for all the help and guidance as we researched these floors. Any tips on cleaning? Do you use any special products or dust mops? Love you floors!! The poly peeled and chopped in spots, especially the edges of the wood. We are putting new unfinished pine in our 100 Percent Tung Oil Day place, too. We read conflicting advice on how many coats to put on and how long to wait between coats.

Do you have any advice? Thank you! Nell — are you talking about tung oil? We covered this in detail in the bottom section of this post. We followed the instructions from the company which I believe are also linked above. That ended up being 7 coats for us — 4 the first day and 3 the second. However, we have found the oil to be MUCH easier to put on ourselves poly is a little touchier and much stinkier. And the oil has held up really well, while allowing us to add another coat in places of high traffic unlike poly, which would require you to start over.

We were very unhappy with the wear of our wood floors and poly in past homes. The pine is a soft wood, so there have been some scratches and dents. The finish is matte and cleans easily with a mop and light water. In places that have more dirt, I just use mild dish detergent and water. Yes, I mean the tung oil. We have also been warned that LL unfinished pine will gap, have you experienced any?

About 6 months in. You can also put down wax paper on the floors to protect the finish. We tried this but it was super annoying and the paper just went everywhere. The folks at Real Milk Paint where we got the paint , recommend days until you walk on the floors with shoes, so I would assume this would be the same for most furniture.

It now appears to be a year from the date of this article. Soooo, did you put the floor in a bathroom? How is it holding up with the tung oil finish? Thanks so much for your article.

The floors have been holding up really well! We plan to reoil the floors again sometime this summer, but they look great and the color has deepened a bit with age which we love. The oil is still holding up to water it beads up on contact. Frankly, I assumed we would have more dings and scratches than we have. We used sheet vinyl, which we love. Drying time will vary depending on the wood, the temperature, and the humidity. It is best to work in a warm dry area.

Always rub away all excess. And if you intend to stain, do not use a sealer stain, as Tung Oil will not penetrate through the sealer. Instant, Brushless Finish Coat. View all products by this Manufacturer. Product MSDS page1 page2.

All rights reserved. Privacy Notice Contact Us All trademarks and registered marks are the property of their respective owners. Rubs In like an oil, dries hard like a varnish!

All of these must first be removed because the oil must penetrate into the wood. Just follow the simple label directions. This will give you greater coverage and help the oil penetrate. We find the ideal way is to thin it… half Tung Oil and half Paint Thinner. How to Apply: You can apply as many coats as the wood will absorb. This may be one coat or it may take many coats. Always wipe away all oil that does not penetrate. Remember, you want the oil in the wood, not on the surface!

Allow each coat to dry thoroughly and buff with fine steel wood between coats. Drying time will vary depending on the wood, the temperature, and the humidity.

It is best to work in a warm dry area. Always rub away all excess. And if you intend to stain, do not use a sealer stain, as Tung Oil will not penetrate through the sealer. Hopes percent Tung Oil- 16 oz.

Free Woodworking Plans Download Java Cost To Build A Frame Lake House Near Me Build A Frame Chicken Coop 2019