Wilton Belt And Disc Sander 02,Family Craft Ideas For Adults Inc,Rikon Belt Sander 50 151 White,Pocket Hole Jig Workstation Number - Step 2
In Stock, 2 available. Part Number: TS In Stock, 4 available. In Stock, 9 available. In Stock, 6 available. In Stock, 8 available. In Stock, 20 available. In Stock, 14 available. Part Number: A Part Number: A. Part Number: B. In Stock, 7 available. Part Number: A-B Replacing the platen on a belt sander is a straightforward repair, but getting the fasteners back in place can be tricky.
Read this video to learn a handy trick to make re-installing the platen easi This video outlines the basics of power tool and appliance electrical diagnosis. You can use a multimeter to test tool and appliance cords and switches, the two parts usually responsible for electri This article suggests guidelines for power tool care and maintenance.
It also describes information tools available at eReplacementParts. Shopping Cart. Submit Search. Sign in Sign in with Password. Cart Shopping Cart 0 item s in your cart. Restore a saved shopping cart. Page 8: Cover The disc sander consists of an aluminum disc onto which is installed an adhesive-backed sanding and other abrasive discs.
The disc is contained within a ducted shroud. The sanding disc can be replaced by removing the table and a cover over the lower portion of the disc. If desired, the aluminum disc can be removed from its drive shaft to ease replacement of the sanding disc. Page 9: Operating Instructions Operation This section defines the controls and other features with which the operator should be familiar.
Refer to Figures 3 and 4 for some typical sander operations. Figure 3. Contouring with Belt Sander Figure 4. Page Disc Table Adjusting Platen Housing Position The sanding belt can be operated with the platen housing horizontal, vertical, or at any angle in between.
The numbers in parenthe- ses throughout the manual correspond with reference numbers for parts shown in the exploded views in the Replacement Parts section. Lubrication The bearings used in the sanding machine are sealed, pre-lubricated bearing. Page 12 9. Install plate 55 and secure with four screws Check for clearance between plate 55 and the sanding disc.
Install table 60 onto rod Position table so it is level and tighten screw 65 against rod Disconnect electrical power. Remove four screws from Wilton Belt And Disc Sander Youtube base. With assistance of the second person, lift base from stand. NOTE: Place base on bench. As an alternative, the stand may be used to support the base while remov- ing drive motor screws. Motor is defective 2. Figure 27 and 28, below: Wiring diagrams for and VAC with push button switch.
Also provided are parts listings that provide part number and description. Item numbers shown on the illustration relate to the item numbers in the facing parts listing. Unpack the dust collection system and check for damage. Contact the carrier if damage is found. Open the installation kit refer to Optional Accessories in the parts listing for installation kits.
Install the cover and debris collection drawer if removed. Page 29 Disassembly Disassembly of the dust collection system is only required to replace the motor or the fan components.
The motor switch, if failed, can be replaced without removal of the motor. Remove the chip drawer 2 and cover 4 from the base 1.
This manual is also suitable for: a a. Print page 1 Print document 32 pages. Cancel Delete. Sign In OR. Don't have an account? Sign up! Restore password. Upload from disk. Upload from URL.
Sugatsune Soft Close Lid Support Device Kreg Pocket Hole Jig 5 30 Pocket Hole Jig With Clamp Quest Making Wooden Pens Round |
Suner_Girl
14.06.2021 at 17:35:14
tenha_urek
14.06.2021 at 14:17:34
add
14.06.2021 at 14:57:54
sauri
14.06.2021 at 13:43:36
anceli
14.06.2021 at 14:20:13