%!$ Easy Diy Woodworking Bench Plans For You #!@

Building this project will make your other DIY projects easier to build. This miter saw stand gives a home to one of your most important tools. It offers removable support wings to hold long boards. Plus, this miter saw stand rolls easily to work where you want to, and then tuck compactly away.

Start by cutting the two Front Legs to length from a 2x4, as shown in the cutting diagram. Drill pocket holes at the locations shown. Cut the two Back Legs to size from a 2x4, as shown in the cutting diagram. Now clamp one Back Leg on top of the first so that the ends are aligned. Then drill a hole through both Legs, where shown, for the wheel bolts. Cut two Handle Rails to kreg miter saw fence parts limited from a 2x4, as shown in the cutting diagram.

Clamp the Handle Rails together, mark the location of the handle hole, and drill a 1" hole through both Handle Rails. Next, cut two Leg Rails to length from a 2x4, as shown in the cutting diagram. Now, drill pocket holes on the inside faces of each Leg Rail, as shown. Finally, bring the Back Leg into final position, and then attach it to the Front and Back Legs as shown. Repeat the process for the other side. Cut four Rails and one Center Rail to length from a 2x4, as shown in the cutting diagram.

Drill pocket holes in each part at the locations shown. Position the four Rails against a side assembly, as shown. Next, attach the Center Rail in between the two Lower Rails, as shown. Slip the Handle into its hole in the Handle Rail.

Position the second side assembly, and then attach it to complete the base. Place one fender washer over a wheel bolt, add a wheel, and then add a second fender washer. Slide the wheel and bolt through the hole in the Back Leg, as shown. Repeat the process for the second wheel. Countersink the holes so the screw heads will sit flush when you attach the Top and Shelf to the Base in the next step.

Position the Top on the Base so it is flush on each side, as shown. Then position the Shelf, and attach it, as well. Every miter saw is different in both size and shape. These next steps will have to be adjusted to fit your saw.

Place your saw on the base and center it side to side. Adjust the position front to back to where it feels comfortable for you. With a pencil, mark the location of each mounting hole in the base of the saw. Place the saw kreg miter saw fence parts limited on the base, and then secure it with bolts and washers.

We used wing nuts so we can easily remove the saw if we need to. The challenge here is that every miter saw is different—some are wider than others, and the saw tables often sit at different heights. That means you need to customize the wings. Our design makes that possible, by letting you cut the parts, and then adjust their mounting positions to set the placement and overall height of the kreg miter saw fence parts limited. Just be sure to kreg miter saw fence parts limited your time and measure carefully as you cut and fit your wing parts.

Next, hold or clamp the Angle Brace in position. Repeat this process to create the other wing base assembly. From a 1x6 board, cut two Fence Backs to length, as shown in the cutting diagram. Drill pilot holes in the Fence Back, as shown. Then align Fence Back with the base assembly, as shown.

Repeat this to attach the other Fence Back. To provide a flat, straight fence surface, you need to align the Fence Backs with the fence on your miter saw. To do that, first slip one wing assembly under your saw, as shown. If the Wing Base hits the underside of your saw, cut enough off that end of the Wing Base so that you can slide it under your saw and bring the Wing Support into full contact with the Handle Rail.

With that done, use a long ruler or reliable straightedge to align the Fence Back on the wing with your saw fence. Then clamp the Wing Support to the Handle Rail. Finally, cut Wing Stops to length, as shown in the cutting diagram. Drill pilot holes in two of them, and mount the Wing Stops so they fit tightly against the edges of the Wing Support, as shown.

From a 1x4 board, cut the Fence Top to length, as shown in the cutting diagram. Then, from a 1x6 board, cut the Fence Front to length, as well. Using a jigsaw, notch one kreg miter saw fence parts limited of each Fence Face, as shown.

Repeat for the other assembly. Mark where the Fence Top intersects the Fence Back. Now mark where the Fence Front intersects the Wing Base. With that done, you can separate these assemblies. Kreg miter saw fence parts limited this to align the fence on the other side of your saw. The wings fit snug, but you may want to add a screw on either side of the Angle Brace that goes into the handle rail.

If you want to remove the wings later, just remove these two screws in each wing. With that, your miter saw station is ready to use. Before you put it to use, though, you may want to wipe on a coat of oil finish, like we did. This protects the wood and makes the miter saw station look kreg miter saw fence parts limited. Difficulty moderate. Shop Now. Wood Project Clamp - kreg miter saw fence parts limited. Wood Project Clamp - 6".

Straight Edge Guide. Crosscut Station. Directions Make the Front Legs Start by cutting the two Front Legs to length from a 2x4, as shown in the cutting diagram. Cut the Handle Cut the Handle to length from a 1" poplar dowel, as shown in the cutting diagram. Make the Rails Cut four Rails and one Center Rail to length from a 2x4, as shown in the cutting diagram.

Assemble the Base Position the four Rails against a side assembly, as shown. Mount the Wheels Place one fender washer over a wheel bolt, add a wheel, and then add a second fender washer. Mount Your Saw to the Base Every miter saw is different in both size and shape. Align the Wing Assemblies To provide a flat, straight fence surface, you need to align the Fence Backs with the fence on your miter saw.

Featured Products. Adaptive Cutting System Master Kit.