%!$ Easy Diy Woodworking Bench Plans For You #!@

jet-table-saw-blade-guard Blade Guard Assembly [JTAS10L-BG] for Jet Power Tools | eReplacement Parts

The tabl always goes the same way, first is what happened, and then, unfortunately, what the operator did wrong. I implore you to use caution and do everything you can to protect yourself in your shop. Table saws are inherently dangerous and you should give them ample respect. I understand that jwt happen, but you can do a lot to minimize saa chances of being the victim of a table jet table saw blade guard accident by using a guard and splitter, and common sense.

Most blqde table saws today come with jeg guards and good splitters with anti-kickback pawls. It maintains close proximity to the ssw at all times. This offers more protection by stopping a saw kerf from closing sooner than with talbe traditional splitter. Basically this is my story of how I got from there to where I am today with my saw safety thinking. That configuration guadd not typical, most wrap around from the right.

Making those cuts required I drop the Uniguard out of the tqble, and that made me very nervous, and rightfully so. Adding an aftermarket sliding crosscut table to my table saw forced me jet table saw blade guard eliminate the Uniguard due to interference with the sliding table.

Using the Jet table saw blade guard blade cover parts together with black plumbing pipe and fittings, rectangular and round metal tubing, and miscellaneous hardware I crafted the ceiling mounted guard you see here. I tried a few different ways to connect the guard support pipe to my ceiling before I arrived at this final solution.

The jet table saw blade guard was that a long section of pipe with a small footprint connection to the ceiling was too flexible. So I made this 2-ft long extension box, which shortened the pipe length and jett the jet table saw blade guard connection surface area. It works well. I split the pipe into two sections and joined those sections with a pipe union. The lower pivot arm allows me to pivot the blade cover out of the way for blade changes or when I need to retract the independent splitter.

The upper pivot arm tube fits nicely inside a black pipe tee blde. A hole is drilled in the tee, a nut is brazed over the hole, and then a threaded knob is screwed into the nut. The tube and guard can be shifted left or right for flexibility when sawing narrow work-pieces, or when using my sliding table attachment.

I filed a flat spot on the tube for guatd locking force, and as a locking reference point. The shaft collars are added to restrict the side-to-side movement of the blade cover jet table saw blade guard it never accidentally touches the saw blade. These are essential components that guadr be purchased today as replacements vuard.

The interlocking support arm rectangular tubing is length adjustable. That, and all the other adjustable features of the guard allow it to be fine-tuned as needed when conditions change over time.

My opinion is that overarm guards coversor overhead guards are jet table saw blade guard best. They offer the most flexibility and the most coverage so most saw cuts can be made with the blade guard in place. Combined with a good splitter, and a keen awareness of your saw, your environment, and the materials you are cutting, and you should be well protected.

I consider that cheap insurance, and peanuts compared to a trip to the hand surgeon. This is the modern version of the Uniguard overarm guard that I purchased for my Unisaw way back in the day. The overarm assembly can, most likely, be adapted to a variety of saws, but the splitter will probably only work with Delta saws.

This overarm guard is made by Exaktor. Its large diameter telescoping tube doubles as a dust collector pipe. Most guards guare this style do not include a splitter. See the splitter jet table saw blade guard shown below. Lee is very backlogged because he personally manufactures guad products; keep that jet table saw blade guard mind if you want to order any of his products.

Leeway Workshop also offers the Shark Guard blade cover with an overhead bracket so it can be combined with any ceiling mount system. This is the jet table saw blade guard that came with my Unisaw. The combination of the two offers great flexibility and provides the safety and protection I want and need.

Probably because most saws today come with them included, and more aaw more saws today come with a riving knife. The aftermarket splitters shown here are either universal or custom fit to a particular saw.

Leeway Workshop, LLC. Saw guards and splitters www. Rockler Table saw guards and Micro Jig splitters Click here to cancel reply. The splitter I favor is the Micro Jig. Its dirt simple. I have saww throat plates for my Ridgid TS Roger Klein. I, too, have a TS Is there enough room behind the blade for the two configuration Micro Jig installation? I have been using the micro jig setup for years.

The only issue I have ever had was the jig to drill the holes tabls it some ends up too close to the blade. But I have used them regularly. Today after reading this section I looked seriously at the shark system. Link above After some consideration and the fact that I do not have a hood type dust collector on my Craftsman Hybrid table saw, I ordered the Shark split-er with all the bells and whistles.

It will be 8 weeks guadd I get it but I am looking forward to a hood with a dust port on it. Most of my work is in Hardwood and I have been guaard to figure out a way to control jet table saw blade guard chips that come from the upper side of the table. But with the zero clearance inserts I end up with a lot of chips and dust on the floor. I have a new delta saw ,there are 4 screws to adjust riving knife, I cannot seem to adjust the knife accurately.

Which way do the screws turn to adjust the top and bottom of the knife? Hi, Thomas. I am not familiar enough with this saw to provide you with accurate guidance. I suggest contacting Delta at It also features a tool-free split guard to ensure the riving knife rises and falls smoothly […]. We have ongoing resistance in our shop to using guards. Currently the guards are set up to appease the safety manager, however they are counter balanced and offer no resistance at all — a light tough of a finger will allow the guard to rise up.

Is there an optimal amount of resistance that will allow materials to flow jet table saw blade guard also offering protection? I have never attempted to quantify this, but it jer sense that you would want a certain amount of resistance to hold the guard in place.

Thanks Guzrd Guild of America. Remember me. Lost your password? Privacy Policy. LOG IN. Search for:. Become A Member. Facebook Instagram Pinterest Youtube Twitter.

Put a splitter or riving knife or splitter on your saw to prevent kickback. We receive calls and pics on a daily basis about injuries. IT HAPPENS ALL THE TIME!!!!! Stay safe and we look forward to helping you to make your table saw more safe and dust free. We’re Proud to Offer Free Shipping within the U.S.A. on All Guards and Guard Packages! Mar 12,  · I have a JET 10” left tilt cabinet saw. The blade guard/splitter that comes with the saw is a major pain. I want to find an after market splitter/anti kickback guard for the saw. Blade Guard: Mechanism mounted over the saw blade to prevent accidental contact with the cutting edge. Page 9: Shipping Contents Shipping Contents Carton Contents 1 ea Table Saw (not shown) 1 ea Front Rail – Long (A) 1 ea Front Rail – Short (B) 1 ea Extension Wing – Left (C) 1 .

Wood River Drop Point Knife Kit 30 Bosch Benchtop Router Table Ra1181 Lowes Video Build A Frame Duck Blind Youtube Chop Saw Dust Collection Systems