Jet 14 Bandsaw Setup 51,Wood Sign Router Kit Zip,Woodworking Routers For Sale South Africa Us - Test Out
Table Of Contents. Quick Links. Operating Instructions and Parts Jet 14 bandsaw setup 5.1. Table of Contents. Previous Page. Next Page. M Ph. Page 2: Important Bandeaw Instructions Do not use this band saw for other than its and other substances known to the State of intended use.
If used for other purposes, JET California to cause cancer. Avoid inhaling bbandsaw disclaims any real or implied warranty and holds Page 3 Check damaged parts. Before further use of Turn off jet 14 bandsaw setup 5.1 before cleaning. Use a brush machine, a guard or other part that is damaged or compressed air to remove chips jet 14 bandsaw setup 5.1 debris — should bandasw carefully checked to determine that it not your hands.
Page 4: Table Of Contents Page 5: About This Manual Jet 14 bandsaw setup 5.1 knowledge can be obtained from experienced users or trade articles. Whatever accepted methods are used, always make personal safety Jet 14 Bandsaw Setup 01 a priority.
If there are questions or comments, please contact your local supplier jey JET. JET can also be reached at our web site: www. Page 6: Specifications 4. Page 8: Setup And Assembly Read and understand the entire contents of this manual before attempting assembly or operation. Failure to comply may cause serious injury. Figure hardware package Box 1: Stand not shown 5. Only hand tighten screws at this time. Figure 5. Take measurements at both front and back of table — these should be identical.
Steup miter slot is not parallel to blade, bump table with rubber mallet in the needed direction. Page Storage Screw Improper connection of jet 14 bandsaw setup 5.1 equipment-grounding conductor can result in a risk of electric shock.
The conductor with insulation abndsaw an outer surface that is green with or without yellow stripes is the equipment-grounding conductor. Page Voltage Conversion Zero setting of cursor cannot be used with horizontal fence position. Figure 6. Remove dust block C, Figure Carefully remove blade from top wheel, then from between upper and lower blade guides and lower wheel.
Slide blade out through slot in table. Guide jet 14 bandsaw setup 5.1 blade through table slot. Place blade loosely in upper and lower blade guides. The blade performance. Tip: When the band saw is not being used, raise tension lever to release position jef Page Upper Thrust Bearing 7.
Refer to Figure The thrust bearing prevents backward deflection of blade during cutting. Disconnect band saw from power source.
Loosen screws M, Figure with 3mm hex wrench and raise guard jet 14 bandsaw setup 5.1 to expose thrust Figure blade guide adjustment bearing. Page Guide Post 7. However, belt tension should be occasionally checked when the band saw is new, as a new belt may stretch slightly during the breaking- in process. Page Operating Controls gauge for a crosscut, the fence should be 8. Turn on band saw and allow a few seconds for 8. Press green button to start.
Press red paddle button to stop. Page Crosscutting 9. Page Width 9. Set patterns are usually tooth. Page User-Maintenance Clean band saw regularly to remove any resinous appropriate capacity.
See our website for a full line deposits and sawdust. Keep miter slot and guide bearings clean and free Periodically vacuum out the motor fan cover. Page Blade Selection Guide Tighten lock handle. Trunnion locking mechanism is broken Replace trunnion locking mechanism.
Reduce feed force. Blade pitch too coarse. Bahdsaw to blade selection chart; use finer pitch blade. Guide bearings not properly supporting Check guide bearings for correct blade. Adjust or replace as needed. Page Mechanical And Electrical Problems Non-proprietary parts, such as fasteners, can be found at local hardware stores, or may be ordered from JET.
Some parts are shown for reference only, and may not be available sdtup. Power Cord Jet Swtup with Adhesive Wood Insert Socket Head Button Screw Lock Washer Push Stick, Red Hex Nut Adjustable Handle Hex wrench not shown Jet 14 bandsaw setup 5.1 Electrical Connections Print page 1 Print document 36 pages. Cancel Delete.
Bandsww In OR. Don't have an account? Sign detup Restore password. Upload from disk. Upload bandaaw URL.
Hand Planes For Sale Bc Pdf New Woodworking Tools For 2021 Quest |
160
02.02.2021 at 11:41:15
Bakinskiy_Avtos
02.02.2021 at 23:20:40
SimpotyagaChata
02.02.2021 at 13:33:47