Central Machinery Belt And Disc Sander Belt Replacement Date,Blum Tandem Soft Close Slides Ii,6 Oak Knoll Road Mendham Nj Type - Test Out
Table Of Contents. Quick Links. Table of Contents. Copyright by Harbor Freight Tools. All rights reserved. No portion of this. For technical questions, please call Previous Page. Next Page. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. Page 2: Product Specifications When unpacking, check to make sure all the parts shown on the Parts List on page 19 are included.
Centrql any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. Page 3: Electrical Safety Do not use a power tool while central machinery belt and disc sander belt replacement date or under the influ- ence of drugs, alcohol, or medication.
A moment of inattention while operat- ing power tools may result in serious personal injury. Page 4 Maintain tools with care.
Keep cutting tools sharp and clean. Properly maintained tools with a sharp cutting edge are less likely to bind and are easier to control. Do not use a damaged tool. See Figure A. Page 7 5. These carry important infor- mation. If unreadable or missing, contact Harbor Freight Tools for a replacement. Never plug the Power Cord of this product into an electrical outlet while standing on a wet or damp surface.
Page 9 Before sanding, turn on the Sander and check for excessively centrql Sand- ing Disc 12 or Belt If necessary, turn off the Sander and correct the problem before using. Always keep hands and fingers as far away as possible from the moving parts of the Sander. Page 10 Allow the Sanding Disc 11 and Sanding Belt 45 to spin up to full speed before feeding a centrral into them.
When turning off the Sander, allow the Sanding Disc and Sanding Belt to slow down and stop Central Machinery Belt And Disc Sander Belt Replacement Adv on their own. Do not press against the Disc or Belt to stop them. Check to make sure the Disc 11 is free machiinery dirt, oil, and other debris. Page 13 Observe the gauge on the Miter Guide Move the Miter Guide to the right or left until the desired angle is indicated on the gauge.
See Figure I. Page 14 Sanding Belt 45 and against the Work Support See Figure K. Apply moderate downward pressure on the workpiece, allowing the Sanding Belt 45 to cut without being forced. Page 15 Sanding Belt 45 and against the Work Support See Figure L. Page 16 Disc. See Figure M. Carefully set the workpiece central machinery belt and disc sander belt replacement date and level upon the spinning Work Table 13 and against the Miter Guide Page Inspection, Maintenance, And Cleaning Power Cord 29 is unplugged from its electrical outlet before performing any inspection, maintenance, or cleaning central machinery belt and disc sander belt replacement date. Before each use, inspect the general condition of the Sander.
Check for bely aged electrical wiring, loose connections, broken parts, loose Central Machinery Belt And Disc Sander Belt Replacement Australia Sanding Disc 12 and Sanding Belt Central Machinery Belt And Disc Sander Belt Replacement Display 45and any other condition that may affect its safe operation. Do not immerses any part of the Sander in liquid. Then, use a premium quality machine oil to lubricate all moving parts. When bept, make sure to store the Sander in a safe, clean, and dry location. Page Parts List Power Cord Power Switch Plastic Joint NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts.
Print page 1 Print central machinery belt and disc sander belt replacement date 21 pages. Cancel Delete. Sign In OR. Don't have an account? Sign up! Restore password. Upload from disk. Upload from URL.
|
Carbide Woodworking Lathe Tools Mac Pocket Hole Jig Uk Screwfix Mp How To Open Hardware Wizard Zookeeper |
KING_OF_BAKU
17.04.2021 at 14:14:55
dagi
17.04.2021 at 18:26:15