%!$ Easy Diy Woodworking Bench Plans For You #!@

woodworking-plans-serving-tray-on 13 Best wood tray plans ideas | wood tray, tray, woodworking projects

Read Reviews 1. This serving tray offers a unique style by incorporating two classic American hardwoods—cherry and maple—along with aluminum bar stock for the handles, and a subtle routed detail that you can add if desired. They tray is easy to build, though, using three boards, the aluminum bar, and some screws. Start by cutting Woodworking plans serving tray on Bottom Rails to size from 1x2 maple, as shown in the cutting diagram.

Notice that the pocket holes are off center. That way, when the center panel gets attached, the holes will be covered up. Now you need to drill four holes, as shown, in line with the pocket holes.

These will be used to attach the outer parts of woodworking plans serving tray on tray, called Wings, later. Learn how to crosscut boards on a miter saw accurately and safely so that you get great results every time. Cut two Handle Rails to length from a 1x2 maple, as shown in the cutting woodworking plans serving tray on. After cutting the pieces, round over the square end of each rail, as shown.

The roundover is fairly small, so you can do it with a sander pretty quickly. It gets added after the Rails are assembled. Learn how to make two kinds of angled cuts on a miter saw: A miter cut and a bevel cut. A miter saw makes them easy, and allows you to expand your project-building capabilities. Lay the Bottom Rails with the pocket holes face up on a flat surface. Then position the first Handle Rail against a Bottom Rail, as shown.

Note that the upper edge of the Handle Rail will sit flush with the upper edge of the Bottom Rail and there will be a slight overhang on the bottom. You can sand this flush after the glue dries. Repeat woodworking plans serving tray on for all four Handle Rails. Learn how to choose the correct Kreg Screw for your project based on the material you are using and where you'll place the project—indoors or outdoors.

When the glue dries on the Rail assemblies, sand them flat. This is woodworking plans serving tray on a good time to sand the Bottom Rail and Handle Rail connections so they are flush. Now you can drill the holes for the aluminum handles.

To assure that the holes align properly, tape the two Rail assemblies tightly together, as shown. Mark the location of the Handle holes and then lay the assemblies on a scrap piece of plywood or wider board to help prevent tearout as you drill through the pieces. Secure the Rails to the work surface with clamps, and drill each set of holes making sure to keep the drill as perpendicular as possible.

Learn how to drill straight holes with a drill by using a simple guide that you can create from scrap wood. Cut two Wings to length from 1x2 cherry, as shown in the cutting diagram.

Sand each Wing smooth. Learn how to use a router safely and get great results with a simple tip that ensures you're always moving the router in the right direction. Apply glue along the flat edge of the Wing, and then align it with the Rail assembly so the upper face of the Wing is flush with the upper edge of the Bottom Rail, as shown.

Clamp the Wing in place. Then use the holes in woodworking plans serving tray on Bottom Rail as guides to drill pilot holes in the Wings, as shown.

Repeat this to join the other Wing to the second Wing to the other rail assembly. Cut two Center boards to length from 1x6 cherry, as shown in the cutting diagram.

Drill pocket holes at the locations shown. Apply glue the mating edges of the two Center Boards, align the ends and edges, and then clamp them together. After the glue dries, sand the surfaces flat.

Using the same router set up as on the Wings, rout a cove profile on the ends of the panel but not the edges as shown. Use a file or sandpaper to sand the cut ends smooth.

Then use a woven abrasive pad such as Scotch-Brite to polish the aluminum to a consistent finish. Set the handles into the Handle Rails on that side. Once the glue dries, clean away any excess that has squeezed out. If you intend to use the serving tray for food, you need to make sure the finish is food safe.

We wiped on a couple of coats woodworking plans serving tray on. We applied woodworking plans serving tray on couple coats of Tried and True natural oil. November 23, Quality plans with Plenty of Detail - Great plans, well laid out, plenty of detail.

Easy to follow. I am a beginner who plays around on the weekends in my garage. Built this in a few hours… see full review. What projects would you like to build? Tell Us. Privacy Policy Terms of Use.

Reviews Likes Builds Views Print Directions. How To Crosscut Boards on a Miter Saw Learn how to crosscut boards on a miter saw accurately and Woodworking Plans Serving Tray Rose safely so that you get great results every time. How To Choose the Correct Kreg Screw Learn how to choose the woodworking plans serving tray on Kreg Screw for your project based on the material you are using and where you'll place the project—indoors or outdoors. How To Drill Straight Holes with a Hand Drill Learn how to drill straight holes with a drill by using a simple guide that you can create from scrap wood.

How To Rout in the Right Direction Learn how to use a router safely and get great results with a simple tip that ensures you're always moving the router in the right direction. Tools Used:. Extras: No extra details have been uploaded. You must log in to add comments Login. Share this plan:. Reviews: November 23, Quality woodworking plans serving tray on with Plenty of Detail - Great plans, well laid out, plenty of detail.

Built this in a few hours… see full review - jordankoczrowski. See all reviews Review Free Woodworking Plans For Serving Trays Online this plan. People who have built this:. See all builds Submit a build. Related plans:. Wall-Mounted Wine Rack. Stylish Serving Tray.

Bar Cart. One-of-a-Kind Cutting Board. Wooden Gift Box. Become a Member Explore Woodworking plans serving tray on with the BuildSomething Community See what others build and share your stories Contribute Find inspiring ideas for your projects you can build Get the step-by-step plans you woodworking plans serving tray on to succeed Share Turn your projects into professional-looking plans Share woodworking plans serving tray on plans you create on buildsomething.

Sign in! Shop Online.

Serving tray woodworking plans. Feb 4 serving tray plans from around the web. These serving tray plans are for the novice to intermediate woodworker. There are lap trays serving trays bed and bath trays laptop trays and more Free Woodworking Plans For Serving Trays System that are perfect for yourself or a thoughtful gift. See more ideas about wood tray tray woodworking projects. This Do-it-yourself projects category features a collection of DIY free woodworking plans to build many types of trays from woodworking related web sites. The woodworkers construction information found on these sites range in quantity and quality. Build a wooden serving tray with charm. All you need is a miter saw, a Trays - All Types. Serving Tray: This serving tray is made from cherry and big leaf curly maple veneer, but could be made from any combination of hardwoods. The overall size is 14 ¼” wide and 19” long. The height is 2 ¾”. 53 pins.

Build A Cold Frame Greenhouse Jp Vision Hardware For Special Conditions 2021