%!$ Easy Diy Woodworking Bench Plans For You #!@

watco-danish-oil-how-to-use We applied Hoe Oil liberally until the block stopped absorbing the oil. This site uses cookies: Find out more. Varnished, shellaced, lacquered or heavily stained wood will usually present a surface barrier dxnish absorption of the Danish Oil, and will need to be removed as necessary with a proprietary paint stripper. If you have an account, sign in now to post with your account. There are other finishes that would be better if you were going to watco danish oil how to use straight from the scraper to finishing. Second, you can experiment with how thick or thin you make it.

Several thinner coats typically produce better results than a couple of thick coats. Level out the finish using sandpaper backed with a hardwood block.

Change sheets often, as shellac will quickly clog sandpaper. For a glossier finish, buff out the shellac with steel wool and mineral oil, proceed to dry rottenstone with a soft cloth, then top with a coat of hand-rubbed wax. Shellac builds in layers, with each subsequent coat dissolving into the previous one. Build layers; then top with a thinned coat to minimize brush marks.

The term "cut" refers to the number of pounds of shellac flakes mixed into one gallon of alcohol, so a two-lb cut has two lbs of flakes in a gallon of alcohol. To make a pint of 2-lb-cut shellac, you need to do a little math. There are 32 ounces in 2 lbs, and 8 pints in a gallon, so 32 divided by 8 equals 4 ounces of flakes.

To mix your own shellac, pour a measured amount of denatured alcohol into a glass or plastic container. Weigh the proper amount of shellac flakes. You can find inexpensive scales at office-supply stores. The finer the flakes, the easier they dissolve, so crush the flakes in a clean cloth before adding Watco Danish Oil Application Notice them. Placing the container in a pan of hot water also helps speed the process.

Once the flakes dissolve, use a paint filter—available at paint stores or home centers—to strain the liquid into a clean glass jar. Label the jar lid with the cut information, color, and date it was mixed. To mix up your own shellac, start by determining how many ounces of flakes you need to produce a certain cut, then weigh them out. Strain the shellac before using it to remove impurities and any undissolved flakes. After I milled some custom oak molding, then stained and finished it to match the existing woodwork Skip to main content.

Three great finishes that aren't polyurethane. Danish oil: Watco Danish Oil Natural Near Me Smooth and easy When it comes to bringing out the natural beauty of a highly figured piece of wood, such as quilted maple or quartersawn oak, nothing beats a hand-rubbed Danish-oil finish. Facebook Pinterest Twitter Text. Printer-friendly version. Read more about Finishes and Finishing. Give old furniture a good cleaning. How can you eliminate brush marks when finishing? For a tough finish, use epoxy.

How to get consistent stain on problem woods. For more related content, subscribe to our newsletter! Keep small cutoffs from escaping at the bandsaw.

Pegs provide positive grip on shop jigs. Head off scratches with a light polish. Boom goes the accessibility! Tip of the Day. Magazine Subscribe Magazine Customer Service. After the second coat has been applied like this, let it dry overnight, possibly a day or 2. But for the first half hour of drying, keep an eye on it to make sure no oil is seeping back out and pooling on the surface. Once that coat dries, if you still see any open pores, repeat the process with another slurry coat.

Once the coat has dried and it appears perfectly flat, apply a final thin layer to help seal in the slurry coat, or you can add a coat of wipe on poly to finish it up. For extra protection, add a second coat of wipe on poly.

Be sure to lay out the rags flat until they can dry, then throw them away.. If you make your own Danish oil, make sure the main ingredients have dryers in them, like boiled linseed or tung oil. Also, do not use non-drying oils like mineral oil. If you use turpentine, get the kind that is made from pine. This smells much better than other kinds of turpentine. When you mix your own Danish oil, do it in a glass jar with a metal lid.

If you use a plastic container, oxygen can get into the mix and over time can ruin the finish. A glass jar sealed tight with a metal lid will have a longer shelf life. They claim to follow FDA regs that makes it safe to use on kitchenware and toys. Thanks for stopping by, and be sure to sign up below so I can send you blog post updates, plus some free plans and templates. Beginning Woodworking? This page may have affiliate links. For more information see my disclosure page.

About The Author Adam has been woodworking for the last 10 years. He considers himself a 'Small Shop Woodworker' and practices his hobby in his garage. With the lack of time, space, and proper tools, he always finds ways to get great results without over-complicating or over-thinking the process.

Various shop jigs, table saw sleds, and tricks of the trade have served him well. God has blessed him with a beautiful family, as well as a passion for teaching others about woodworking. You can read more about Adam here. A really helpful instructive article on using Watco Danish Oil finish. His method was to use the slurry method over a week and wiping off the excess as it dried between coats.

I find it easiest to apply this finish by first transferring some into an old yoghurt container to work out of. Liberally apply the finish over the whole work piece using a brush or rag. You can put on a lot, flooding the surface. After 30 minutes, come back to the piece and reapply finish, particularly to areas where all the finish has been soaked in.

For a typical piece of furniture I will repeat this process to build up 2 or 3 coats. Additional coats will deepen the shine and increase protection.

Once I am satisfied with the number of coats, I will wait 15 minutes, then wipe the surface of the piece completely dry making sure there are no drips or pools of finish. I will touch the finish with my fingertips - it should feel oily but dry and smooth. You must now safely dispose of the oily rag. Improperly disposed oily rags can spontaneously combust.

Hang them outside to dry in a safe area or spread them out flat. They should not be in a pile. Once they cure, the cloth will be hard and brittle and you can throw them out. Question 2 years ago on Introduction. Can I soak new cut plywood scroll saw pieces in Danish oil overnight? Or, dipping it in a tray for 30 minutes? Question 3 years ago on Introduction. Hello and thanks for the video information.

My question is I noticed that you did not sand between coats, is it necessary or not? I am making an unfinished acacia wood butcher block, L-shaped bench for my breakfast nook that will be built-in.

We want something to seal it with something that does not change the color much, yellow like polyurethane and not a glossy finish. We would like to keep it as close as we can to its natural color, maybe a matte or satin finish. We will sand and seal the wood prior to building in a Watco Danish Oil Application Website shop, and prefer not to do much sanding in our home now and in the future. We would like some advice Thank you so much for your time!

Free Woodworking Plans For Beginners Mod Youtube Kreg Pocket Hole Machine Lathe Tools Rockhampton Co Ltd Woodworking Hand Saw Set