%!$ Easy Diy Woodworking Bench Plans For You #!@

mounting-jet-air-filtration-questions I actually own a total… see more I guess it depends on the size of moknting shop needs. Now how in the world are you going to get that heavy beast up to the ceiling? Your friends might wonder auestions you managed to do it mounting jet air filtration questions by yourself. This positive charge gets transferred to the airborne particle. The other ladder was no longer cutting it at this point. I actually own a total of 4 air cleaners, two of which are the stated Jet air cleaners. One can mounting jet air filtration questions argue that the Jet's filtration system, bearings or motor are superior to the WEN and Powertec, but basically, each air cleaning unit involves a two stage filter, a motor and a squirrel cage fan.

This gets hung from the ceiling not on a wall. If you place this in the center of the shop or room it's going to try to pull that dust to the center of room and there may not be any dust ether to begin with why pull dust through the shop if you dont have to? I have one over my Miter station, one over my Band Saw and the third larger unit in the center of the shop.

But if I only had one air scrubber that thing would be wherever the majority of my dust is made, not just in the center or in an arbitrary corner. And always by a few smaller units than one large unit, I made that mistake initally. If you can afford the big version of this just get two of these smaller units and put each one over the ares you create the most dust. Failed to get answers. My shop is 27x27 with 20 ft ceilings.

Will this unit filter the air efficiently in such a large space? Could not say for sure but a couple of comments to possibly make it more effective. I have not put my unit to the test so far … see more Could not say for sure but a couple of comments to possibly make it more effective. I have not put my unit to the test so far to give you a better feel for cleaning capacity but my 13 X 14 shop opens up to a basement storage area o that would make it a similar size to a 27X27 with about a 9 ft ceiling.

So far I have not noticed any excessive dust in the storage area but again i have not really pushed it enough to be conclusive.

It says must be mounted 7feet off floor. Is this just for safety? Are is it for proper operating of unit? I never saw a notice to mount it a minimum of 7 feet off the floor.

Mine is mounted about 1. It is mounted over a workbench so there is no danger of hitting it with work pieces moving around, but it seems like the r… see more I never saw a notice to mount it a minimum of 7 feet off the floor. It is mounted over a workbench so there is no danger of hitting it with work pieces moving around, but it seems like the right height for the unit.

I would think that you could mount it at any height that would make sure you don't hit it with moving your work pieces around. As for operating the unit, it seems to me that the closer you can place it to the source of dust and airborne particulates, is the best place to mount it. Does anyone know why this the prefilter is described as "electrostatic. Here's the answer to how electrostatic filters work from eHow. The fibers have been formulated so that when air passes by them, they generate strong static charges.

Separate … see more Here's the answer to how electrostatic filters work from eHow. Separate layers of filtration material also receive opposite charges positive and negative. Since positively charged particles are attracted to surfaces with negative static charges and vice versa, the filtration media can actually attract airborne particles like a magnet and hold on to them until the filter is cleaned.

When a particle of dust, mold, fungi or any other airborne matter comes from the HVAC system and through the ducts toward the filter, it first passes through a synthetic filter layer with a positive static charge.

This positive charge gets transferred to the airborne particle. Then the particle passes through a layer with a negative charge, and it is attracted to that layer's surface. The more layers of oppositely-charged filtration media there are in the filter, the more effectively it can prevent airborne particles from entering the room. As a result, I got the eyes about an inch closer together on one end. Especially with framing construction.

Connect an S-hook and chain to each eye screw. None of that wimpy, unwelded swag lamp chain. Some shop air filters come with hooks on top, but most have eye bolts. The rest of us can either replace the eyes with hooks or use S-hooks as shown. You will have only one free hand to work with. So after connecting the S-hooks to the air filter, wrap some tape to keep them upright and at attention. Doing so makes it much easier to connect the chain with one hand while lifting the Mounting Jet Air Filtration Model unit with the other.

By now, you can probably see where this is going. As you work your way higher and higher, always keep an eye on the chains opposite you. If one slips off, reattach it before proceeding.

The other ladder was no longer cutting it at this point. I needed something to lean on while lifting the weight near ceiling level, so I switched to a taller ladder. Finally, once you reach the desired height, cut off the excess chain. Or you can just double up the S-hooks by hooking the ones from above through the eyes on the air filtration unit. And hooking the ones on the filter unit through the eyes on the ceiling. At many times during the process, the weight will temporarily be supported by only three corners.

Once you have the unit positioned where you want it, however, check that the load is distributed among all four. If one has slack, adjust an eye screw or hook to snug it up. And there you go — one shop air filtration system suspended from the ceiling.

If and when you ever need to take it down again, simply reverse the process. Your friends might wonder how you managed to do it all by yourself. Steve made his first woodworking project at age 9 in and whittled his first wooden chain at He was also a consumer electronics repair tech and shop owner for a little over 20 years, until his impending obsolescence became impossible to ignore. Since then, Steve has focused passionately on manipulating his wood Don't judge him.

A clever solution to a weighty problem, Steve. Thank you, Phil, on both counts.

Folding Door Hinges Hardware Trading Lathe Tools 10mm 4d Power Carving Burs Ltd Old Branding Iron Designs