%!$ Easy Diy Woodworking Bench Plans For You #!@

grizzly-6x9-belt-and-disc-sander-pdf There is nothing exceptional with the dust collection on this unit. Trained service technicians will be glad to help you. Installing sleeve guard. Follow instructions for samder cating and changing accessories. Page Clean Up Clean up The work table and other unpainted parts of the Model GZ are coated with a waxy oil that protects them from corrosion during shipment.

Page 2 WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activi- ties contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.

Page 5 Keep tools sharp and clean for best and safest performance. Follow instructions for lubri- cating and changing accessories. G Combo Sander Before fur This manual con- tains proper operating instructions for this machine. This machine is part of a growing Grizzly family of fine woodwork- ing machinery. When used according to the DO NOT modify the plug or power cord in any way. Take the time to familiarize yourself with the features of your new Model G Combo Sander.

They will be frequently mentioned throughout the instructions in this manual. Sander Unit Not Shown Disc Sanding Table Most tables and workbenches should be sufficient to carry the weight of the machine. Reinforce the table or workbench if you question its ability to Grizzly 6x9 Belt And Disc Sander Review support the added weight. Inserting the index pin into the base. These are available in a variety of grits. See the current Grizzly catalog for prices and ordering informa- tion.

The PSA sanding disc sticks directly to the sur- face of the aluminum disc and can be replaced without removing either the table or the dust port. Page Aligning Table Repeat steps if the sandpaper touches the table at any point in the rotation.

G Combo Sander Adjusting Miter The miter gauge needs to be adjusted perpendic- ular to the face of the wheel when it is mounted in the table slot. Page Adjusting Belt Angle Slide the belt onto the drive drums as shown in Figure 13 and release the belt tensioning lever. Note—make sure that the arrow on the inside of the sanding belt points the same direction as the belt rotation arrow on the machine. Belt G Combo Sander Page Adjusting Sanding Belt Tracking The dust collection for the sanding disc and the belt are fed into the same port that is located on the end of the sander as shown in Figure Figure Hose connected to dust port.

To connect your machine to a dust collection Make sure the power switch is in the OFF position before connecting the sander to the power source. Page Disc Sanding Figure Disc sanding with a miter gauge. Never use the Model G for applica- tions other than those for which it was made. DO NOT overload the machine or use excess force when sanding. Page Angle Sanding Place the index pin of the disc sanding table in the upper hole in the sanding belt table.

Rotate the sanding table perpendicular to the sanding belt and screw in the knob as shown in Figure Installing the table for belt sanding. G Combo Sander Next Page. Grizzly GZ Owner's Manual 68 pages. Grizzly GZ Parts List 5 pages. Installing sleeve guard. Page 2 GZ manual. Therefore, please use the included Model GZ manual when ordering new parts for your machine, unless those parts are shown above. Page 8: Additional Safety Instructions For Sanders Even if you have a reliable method of dust collection, use a dust mask or respirator when sanding, as well as eye and ear pro- tection.

GZ Combination Sander The use of improper acces- sories may cause risk of injury to persons. FIgure 1. Repair or replace damaged or worn cord immedi- ately. GZ Combination Sander The Model GZ is a combination 6" x 48" belt and 9" disc sander that is capable of a wide vari- ety of operations. The 6" wide belt enables you to sand large areas flat very quickly, and the 9" Save the containers and all packing materials for possible inspection by the carrier or its agent. Page Clean Up Clean up The work table and other unpainted parts of the Model GZ are coated with a waxy oil that protects them from corrosion during shipment.

Remove the protective coating with mineral spir- its and cloth rags. Do not use gasoline or other petroleum based solvents because of their extremely low flash points. Page Assembly 12mm open end wrench, regular screw- driver, Phillips screwdriver, and a 4mm Allen wrench.

The four legs are connected with top and bottom cross braces. Page Stand Figure 3. Bolt the shorter upper and lower braces to one of the 2 stand sub-assemblies. Figure 4. Tighten down all the stand bolts at this time. Page Sanding Unit 7. Make sure the Setscrew is lined up on the flat spot on the drive shaft. Figure 7. Figure 8. Page 16 Tighten the setscrews. Figure GZ Combination Sander Now slide the working table assembly onto the support shaft and tighten the setscrews.

Keep in mind that there should be a between the sanding disc and the table. Page Adjustments Turn the machine on and off again quickly to see if the tracking has improved. If not, repeat step 1. If tracking is improved move to step 4. Now with the sander running, adjust the knob to fine tune the belt tracking.

Page Belt Tensioning Normally steps are done with the belt installed. GZ Combination Sander Use a large open end adjustable wrench and carefully rotate the eccentric, PN 84A to increase or decrease tension.

Woodturning Tools For Sale Australia 2020 Wood Carving Machine Small Table