Craftsman Router Table And Router Combo Mode,Miter Gauge Replacement Question,Dewalt 3436 Radial Arm Saw Fan - Plans On 2021
Table Of Contents. Quick Links. Table of Contents. Product Manual. Sears, Roebuck and Co. Previous Page. Next Page. Garage storage solutions craftsman router table and router combo mode cabinet - all shelves 16 pages. Page 3: Symbol Meanings The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The instructions and warnings they give are no substitutes for proper accident- prevention measures.
Page 4 Some of these following symbols may be used on this tool. Please study them and learn their meaning, Proper interpretation of these symbols will allow you to operate the tool better and more safely.
Failure to fol- low all instructions listed below and the instructions in the product manual for cimbo router may result in serious personal injury. Cluttered benches and dark areas invite accidents.
Page 6 Use only 3-wire extension cords that have 3-prong grounding plugs and 3- pole receptacles that accept the tool's plug. Repair or replace a damaged or worn cord immediately.
Repair or replace damaged or worn cord immediately. This tool is intended for use on a circuit tale has an outlet that looks like the one illustrated in Sketch A in the figure below. Page 7: Personal Safety Table A shows the correct size to use, depending on cord length tsble Craftsman Router Table And Router Combo With ampere rating.
If in doubt, use the next heavier gauge: the smaller the gauge number, the heavier the cord. Before begin- ning power-tool operation, always wear safety craftsmxn or rluter glasses with side shields, and a full-face shield when needed.
We recommend Wide Vision Safety Mask for use over eyeglasses or standard safety glasses with shields. Page 9: Service Safety Do not force the tool, Use the correct tool and blade for your application. The correct tool and cutter will do the job better and more safely at the rate for which it is designed. Disconnect tools before servicing; when changing accessories, such as blades, bits, cutters, and the like.
Page 10 Do not plug the router power cord into a wall outlet. It must be plugged into the router table switch. The large voltage drop would cause a loss of power and the motor would overheat. Page 12 5 inches long and 5mm in diameter, not included. This feature functions only when using the Craftsman router supplied with this table model or the following Craftsman routers: models and Position the legs relative to the router table as shown in Fig, 2.
Position one short end of the table so that it extends beyond the craftsman router table and router combo mode of your Page 15 Fig, 5 The adjusting hole in the table, shown in Best Router Table And Router Combo 20 Fig. Place the fence assembly on the table with the four wing nuts facing toward you. Page Switch Operation Drill a hole at each of the marked locations. Place the router table on the work surface, and align the holes in the routet legs with the holes in the work surface.
Secure the router table to the work surface using four screws not supplied. Page 18 3. To turn the router OFF, Fig. To adjust the extended fence forward and backward Fig, 13 Loosen the two clamping knobs 5. Move the fence forward or backward along the slots to the desired position, Tighten the clamping Craftsman Router Table And Router Combo Off knobs.
The fence can be Make sure the router-table switch is off. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust, craftsman router table and router combo mode, grease, etc.
Page 24 Get it fixed, at your home or ours! For the replacement parts, accessories and owner's manuals that you need to do-it-yourself For Sears craftsman router table and router combo mode This manual is also suitable for: Print page 1 Print document craftsman router table and router combo mode pages.
Cancel Delete. Sign In OR. Don't have an account? Sign up! Restore password. Upload from disk. Upload from URL.
Woodworking Edge Corner Flattening Tool Ball Bearing Slides For Drawers Mod Makita 23 Gauge Nailer Cordless Wifi |
Rockline666
15.05.2021 at 10:33:44
SEVGI1
15.05.2021 at 20:52:10