%!$ Easy Diy Woodworking Bench Plans For You #!@

build-a-frame-for-a-canvas-painting Mitered corners look more professional but can builc difficult on Build A Frame For A Canvas Painting Jobs a stretched canvas. Hope these ideas help you out! Reserve some of your paint to cover over your brads when your frame is complete. Measure the width for build a frame for a canvas painting to sit inside the frame, then trim it with the miter saw. Repeat steps 1 through 6 for the second side of your frame.

Do not assume that the parallel sides will be exactly the same length. As mentioned above, stretched canvases are not always square and even. Take the time to measure and cut each side separately. If you want to paint your lattice, you should do it before you assemble your frame. You can use either acrylic paint or stain to paint your pieces.

My art professors used to say that you should only paint your frame either black or white, but I think you can paint it any color your want, or leave it in its natural wood state.

To paint your lattice pieces:. Mix up your paint color and cover your work surface. Use wood or lattice scraps to prop up your frame pieces. Paint all four sides of your lattice pieces be careful not to cover over your labels , letting each side dry separately. Be sure to paint the underside because it will show a bit on your frame.

Paint in even strokes, being careful not to leave any marks or fingerprints. Let your lattice pieces dry completely before assembling your frame. Reserve some of your paint to cover over your brads when your frame is complete. Before assembling your frame, put down a towel to protect the front surface of your canvas.

Take a piece of your cut lattice and place it in position against the correct side of your stretched canvas, being careful to check the label on the underside of your lattice. Make sure the shorter side of your piece is against the side of your canvas and the beveled side hangs out a little longer. You can either line up your lattice so that it is flush with the surface of your painting, or that it sits a little forward so it creates a small lip in front of your canvas.

With your piece of lattice held in place, use a pencil to mark the placement for your wire nails. Make a dot for your first nail in the center of the length of your lattice. This dot should also be in the center of the width of your lattice. Next, make dots for the nails at each end of your piece of lattice.

Now fill in with additional dots for additional wire nails if needed. Place your nails so that they are about 4 to 6 inches apart, depending on the size of your canvas. Working on a piece of scrap wood, use your awl to make starter holes at each of the spots for your nails.

Using a hammer and holding your lattice in the correct position, begin to nail the first piece of your frame in place, starting with your center nail. Drive this nail only about halfway in place. Repeat steps 1 through 6 for the second side of your frame. Carefully fit your mitered end into the corner of your first piece. When you get a good, tight fit for your mitered join, you can nail all your brads on that corner in place.

If you can't get a good fit at your mitered corner, you have two options: cut a new piece to fit, or work the two pieces you have to fit together so that at least the front visible corner looks good. You can also use some wood filler to fill in any gaps. Continue steps 1 through 7 to fit and Build A Frame For A Canvas Painting Mac nail all four of your frame pieces together. Use your reserve paint to touch up any areas and cover your nail heads if necessary.

My husband and I make our frames with non-mitered corners if that's a word. We cut the top and bottom pieces so they are long enough to cover the cut ends of the side pieces see photo above. I actually like the way this looks.

I think it has a more contemporary look to it. Measure the right and left sides of your canvas separately. Again, don't assume that they are the same length. Using a miter box, cut each of these pieces so they fit the exact length of each side.

Use a straight cut with your piece of lattice lying flat against the bottom of your box see photo above. Sand the ends and be sure to label the underside of each piece with the side it fits. Now measure the top of your canvas, holding each of your two cut pieces on the appropriate sides. Include the depth of the side pieces in your overall measurement for the top see photo at the top of this section.

Follow the directions above for painting your frame pieces if you want and assembling your frame. Your non-mitered corners should fit together more easily. Materials for hanging your stretched canvas you can use these materials and process whether your canvas is framed or not :. Place your canvas face down on your work surface with the top away from you and the bottom of the canvas closest to you. You may want to put down a towel first to protect your artwork.

Starting on the left hand side, use your pencil to make a mark on the center of the stretcher that is one third of the way down the height of your canvas. Repeat this process on the right hand side. Use your awl to create a starter hole in each of these marked spots. Your art dimensions should include the full measurement of your painting that will show on the front surface of your finished framed piece.

Carefully roll your unstretched canvas vertically versus horizontally to put the weight on the outer edge instead of a side. Keep the roll loose and the paint on the outside to minimize the risk of damage.

This might seem counterintuitive, but rolling with the paint on the inside may cause the paint to crease or wrinkle. Share this post. Other posts you might like Art of Women, by Women. Color Pops with Anabeth. Hold your spacer in the corner on the front of your painting and on the other side apply hot glue to each of the backside corners of the canvas. As an Amazon Associate and member of other affiliate programs, I earn from qualifying purchases.

I love how these turned out! I also love gallery framed canvases because you can paint the edges. I may have to make some frames now for some of my other pieces! Active Time: 15 minutes. Total Time: 15 minutes. Difficulty: Easy. Instructions Measure your canvas painting's dimensions and write them down. Cut your frame out of the 1x2 using the canvas dimensions and a 45 degree miter cut in each corner.

Stain and seal your frame. Install the canvas print by applying hot glue to the back corners of the print inside the frame. Notes Staining and sealing are optional. Recommended Products As an Amazon Associate and member of other affiliate programs, I earn from qualifying purchases. Or did you stretch it yourself? It was an already stretched canvas.

Woodworking Bench Design Material Woodworking Projects Catalog Design