%!$ Easy Diy Woodworking Bench Plans For You #!@

tambour-door-router-bit-set-error This seems reasonable and worth trying before doing something more drastic. View Details. Need some inspiration? Errror recently fabricated my first set of tambour sliding doors for one of the buffets in an art tambour door router bit set error piece - the doors looked beautiful and the channel they would slide in perfectly matched the template. A line drawing is more than enough to visualize and calculate the problem. Pre-fab channel that is compatible with the pictured pre-fab slats; of course, a straight channel ttambour also available.

Idealized tambours with thinner tenon to hide the track going around a circle. Focusing in on just the thickness of the tenon removes some unnecessary detail masking the problem area.

A line drawing is more than enough to visualize and calculate the problem. In fact, we do not even need multiple tenons in the drawing. The problem is that the gap between the corner of the tenon in the lower right or lower left is very Tambour Door Router Bit Set Off close to the outer edge of the channel.

With this simplified drawing - and with the real dimensions from my slat and channel - I immediately see the problem. Understanding this, there are four possible solutions to my predicament:.

Going from the drawing and understanding to an equation, the smallest gap at the corner of the tenons as the tenon rounds a channel in the simplified drawing above can be calculated with a few variables and the Pythagorean theorem. Clearly this is too small. This seems reasonable and worth trying before doing something more drastic.

I carefully protect the finished face of the door as I slide it thru the table saw, cut, and voila - my fear of a lost week of work is removed with a few hours invested here. I now have a set of smooth-sliding tambour doors! And of course, there are other considerations as well that limit going to an even tighter radius: the tenon must be thick enough to have substantial strength as the door slides over decades of use; and the tenon should not be so much narrower than the channel that the door is wobbly in the straight sections.

In the final assembly when I again ran into some binding, I had suspected the former problem, until I ran the numbers and realized I was getting caught up due to the second problem. The lead strip may be a little wider to made it clearly visible and perhaps provide a mounting point for a knob or handle.

Finally, the feed-in channel: this is Tambour Door Router Bit Set 90 what provides the entry for the door after the casework is prepped. Though you could potentially build the casework around the door, that can be challenging to do with respect to having enough hands to hold everything in place. But more importantly, it provides an access point for you to service the door if ever needed just by removing the back panel. However, typically, the feed in channel has a radius in the opposite direction than the curves the door will have to traverse most of the time.

While there is a little play in a canvas backing, a well-made door cannot flex very far in the opposite direction. Thus, you may have to use a much larger radius - or enlarge the channel - at the exit. Even if, with a lot of elbow grease, you can finagle the door into the track, should that door ever need service years down the road an extra hour widening the track now will save your future self - or a refinishing shop - many many hours trying to force the door out later. This is the track I cut - note the relatively small-radius lead-in channel at the top center.

The first bit shapes the face of the stock; cutting from each face completes the contour of the ball. Afterward, a second bit is used to shape the socket. A third bit in the set is used to shape the end of the tambour which provides a place to mount a pull for opening the completed tambour.

Carbide tipped. The set comes with a full-color instruction manual for creating a breadbox. Need some inspiration? Check this out! Tambour Door Video. How tight a turn can this door make. I am planning on building a cabinet with a horizontal install.

Door will sweep and then need to do a 90 to park in the open position. About how much production can I expect From a set of bits and can hard woods be used. Yes, it can be used on hardwoods.

Craftsman 75 Radial Arm Miter Saw Chisels Of Carpentry Shop Youtube Marking Knife Kit 90 Desk Drawer Hardware Group