%!$ Easy Diy Woodworking Bench Plans For You #!@

make-thors-hammer-out-of-wood-park Did you make this project? After I had them all cut out I punched holes in them so I could sew them. Telescope Setting Circles by instgct in Science. Covered Bridge and Maple Trees. After I had everything primed and sanded, I applied two coats of paint. I got it from my work but it's just insulation foam. Well done :.

I taped the disc up to match the rest of the hammer and glued it to the top. To make sure it adhered well I put it upside down on the table and put some heavy blocks on it. I gave both the sledge and the wooden dowel a couple good coats of grey and then a light dusting of silver. There are a lot of different variations on Thor's hammer so you can do the handle several different ways depending on the look you're going for.

If you want to go the really simple route you could wrap it in strips of cloth but I wanted mine to be at least kind of similar to the movie so I decided to do a leather grip. I figured out how long each strip needed to be to go around the dowel and then cut them out in a sort of wavy pattern.

Each strip was about an inch and a half in height. You can cut them out with a really strong pair of scissors or a good utility knife with a brand new blade. After I had them all cut out I punched holes in them so I could sew them. I used a leather punch, but you can use an awl or a nail or really anything sharp.

I sewed them on with a large needle and some waxed thread. I also put glue under them as I sewed them on to make sure they stayed in place. For the final touch on the handle I attached a loop on the end. I cut a thin strip of leather and using really tiny nails I tacked each end of the strip to opposite sides of the dowel. Then I cut another strip of leather and wrapped it around the butt of the handle to cover where I had attached the loop. To attach it I used the same method I used for the rest of the grip.

I put rubber bands around each strip of leather as the glue dried. The last step is simply to glue the handle into the hole you made in the sledge. If you find the hole is slightly too big you can wrap tape around the dowel rod until it fits tighter. Then just cover the dowel with glue and put it in the sledge. Make sure you cover it really well with glue.

Also, when you put the handle in make sure it stays straight until the glue is totally dry. You don't want to turn your back and find that it dried crooked.

Now you're ready to save the world! Where did you get the foam, and how soft is it? Like, if someone were to be hit with it, would it hurt? Reply 5 years ago. I got it from my work but it's just insulation foam. You should be able to get it at your local hardware store or building center. If you can't find it thick enough you can laminate pieces together. As far as how soft it is, that's kind of a tough question to answer. It's a pretty light material so it would be hard to inflict much pain but it would still hurt if I konked someone upside the head with it.

At risk of sounding stupid here, how did you attach the leather strips to the wooden dowel? Any ideas on where I can find leather strips like these to buy? Reply 5 years ago on Introduction. I actually glued and stitched almost as one step. Basically I put some glue on a strip, positioned it where I wanted it, and sewed it up.

It gives you a little time to work with it. As far as the strips themselves, I recommend buying a bag of scrap leather from Tandy, ebay, or a craft store and cutting them out.

You can get them the shape you want and you should have a good amount of leather to play around with afterward. Technically you can also buy strips of leather from Tandy but it's usually more expensive to buy it that way and you will have less options when it comes to your final shape. I need to try this! As soon as I get the materials! I also want to make an iron man helmet! I made one out off two bricks and lots of cement and it's really heavy!

That is quite impressive. A word of advice, a lot of times you might find contractors willing to give you scrap material that they would just throw away otherwise, if you ask nicely. I'm making this for friday but I can't figure out how you've done the stitches in the handle! Reply 6 years ago on Introduction. Basically I just had to angle the needle through the holes. More often than not I put it through one hole and out the top and then angled it back under to come out the next one.

Its a solid lbs. I have always been a fan of super hero movies for some reason. If you aren't familiar, Thor is the god of Thunder and is adapted to be in his own Marvel comic series.

In the series, he wields a hammer that only himself and a select few with magic powers can even pick up! So the hammer in theory weighs so much no mortal man can touch it. So i figured, why not make on! In the video I walk you through some traditional woodworking techniques on how i made the hammer, and i also smash a ton of stuff at the end. This may not be a traditional build from my end, but i hope you enjoy!

Affiliate links are posted on this page. For more information on my Affiliate disclosure, check out my Disclosure Page. If you want to see me make more stuff like this leave a comment and tell me what you wanna see! Want to try this build out for yourself? Download the digital plan now for step-by-step instructions, measurements, and a detailed look at how to punch this project in the face.

I used to be an offensive lineman in the NFL, Now I run my own furniture business and am completely self taught. In my videos and posts you'll see a variety of wood and metal work as well as some tips and tricks. Pittsburgh-based custom wood and metal worker.

Best Cnc For Woodworkers 001 Soft Close Drawer Slides Ratings Pdf Bulldog Router Table Quit Types Of Hand Plane Tools 2020