%!$ Easy Diy Woodworking Bench Plans For You #!@

make-a-picture-frame-with-a-router-setup How to make your TV picture look better than ever - CNET

Thank you to Minwax and JET for sponsoring this project! Before routerr get started, make sure to follow me on YouTubeFacebook and Instagram to keep up with all my latest builds! This page uses affiliate links. See my disclosure page for info on affiliate programs. The first frame can be made using just a miter saw and a handheld router. Most miter saws have holes in their fences to attach an additional fence. Next I swung my saw 45 degrees to the left and made the initial cut in the fence.

Then I made a series of test cuts to see how well it lined up. And by some woodworking miracle it was perfect. I used a make a picture frame with a router setup I picked up from Rrouter Peters and made some reference lines on the fence.

Then I used a 45 degree drafting square to draw lines parallel to the cut the line. Next I grabbed my handheld router to make a spot for the picture and glass. Next I started to cut the miters.

When cutting picture frames you really have three different measurements. The outside length of the frame, the inside length of the frame and the length of the rabbet. The rabbet is the only one you need perfect because it holds your artwork.

You can just line up the end of the rabbet with the mark for the size you want. This will give you a perfectly sized recess for your glass and artwork. I stacked one on top of piture other and cut the setu; 45 degree angle at the same time. This way if the pieces are slightly off the mark they are still the same size. I repeated the process, establishing a correctly angled miter on the remaining make a picture frame with a router setup first, then cutting them to size.

I lined up the parts end to end and used tape on the outside corners where each piece met. This let me fold up the joint without the parts moving. I used a special glue on the miter joints to help make the end grain joint stronger.

I put it on all the joints then folded them up and taped the last corner. Then I used more tape to try and pull the corners tight. That said, it did work, but the setkp needed some reinforcement. A DIY version of reinforcement is to use these corrugated fasteners. They get hammered in across the miter joint and lock it into place. After the glue was dry, I held the fasteners in place with pliers and hammered them make a picture frame with a router setup. I kept bending the fastener and it was really just a mess.

One was good, two were so so and the fourth was a complete disaster. When Woodworking Make Simple Picture Frame Uk I tried them out on a plywood test frame they worked great, so I think if you get your technique down right these are a good option. Also I made an identical frame from poplar to show the difference make a picture frame with a router setup the two woods, so I made some sample sticks to test the stain.

I applied pre-stain conditioner to the poplar test stick and one pine stick. This helps even the absorption of the stain and reduces blotchiness.

The Espresso ended up being the one I liked the best and the conditioner definitely helped reduce blotchiness, so I went with that combo. Making test sticks like this is a great way to hone in on the look you want.

My favorite way to apply stain is with a shop towel and I wiped on a coat of the stain to both the pine and poplar frames after pre-treating them with the conditioner. The conditioner reduces blotchiness and makes the stain absorb evenly. I ended up doing 3 coats to get to the darkness I wanted. After letting it dry I came back and topped the frame with a Minwax clear aerosol lacquer in satin. I love this lacquer because it dries very quickly and I could go back and forth between the frames almost immediately.

Making a Picture Frame using a Table Saw. The first cut to make is a subtle chamfer on the inside pictuee the frames edge.

I tilted the blade to 15 degrees and set the fence a half inch from the blade. Using a featherboard for these cuts makes sure the cuts are consistent along the entire piece. With the chamfer cut I could move on to the rabbet for the glass and artwork. For the last cut I flipped the board on edge then moved the blade and fence to line up with my last layout make a picture frame with a router setup. I cleaned up the saw marks on the frame with a card scraper before heading fgame to the miter saw.

This thing makes clamping mitered pieces so much nicer. The little corner supports span both sides of the miter giving you even pressure around the whole frame. After the glue dried I wanted to add some splines for support. So I used a jig to position the frame and cut a slot in each corner. Then I sized a piece of oak to make a picture frame with a router setup the slot and cut out little triangles on my JET bandsaw.

I flattened the bottom of each triangle on sandpaper to make aith it had a solid fit. Then I glued them all in place making sure the triangle was bottomed out in the slot. After the glue framr I cut the splines off with Picture Frame Moulding Router Bits Location a flush cut saw.

Be careful to cut with the grain here and not ,ake it or Make A Picture Frame With Glass the corner can chip out. I finished by sanding them flush with the frame. I used the Minwax white wash pickling stain and applied two coats. After letting it dry I top coated the setip with Polycrilic by Minwax which added protection.

This is a new take on oak which is not one of my favorite woods but the white wash definitely changes the feel. For the third frame I brought out the big guns and added a router table to the mix. With a router table you open up a whole new world of options for profiles.

I had a rough idea of what I wanted to do with the profile, but honestly I just jumped into it. Using a farme bit, I made a sweeping curve on the inside of make a picture frame with a router setup frame. It was a little small for what I was going for so I raised the bit and made another pass.

Next I unplugged the router and changed over from a cove bit to a straight bit. This is very subtle but will create some really cool shadow lines in the final piece. The possibilities really are endless when doing profiles on the router table. Cutting the recess rabbet for the glass and artwork can be done with the same straight bit. And the dust make a picture frame with a router setup on this table is superb with both above and below the table collection points.

With the more detailed profile I needed to sand everything before assembly. Wrapping sandpaper around a dowel is a great way to get into the curved areas. I went through the same process on the miter saw to cut the miters. Frankly I was make a picture frame with a router setup to cut them on the table saw using a jig but my results were so good with the miter saw and auxiliary fence I just stayed with it.

For this frame I went back to the taped corner method but paired it with rourer web clamp. I got overconfident in the web clamp with the oak frame and the corners did slip a little up and down. This combination gave me my best results yet because the profiles in the corners met up perfectly.

I went with a clear aerosol lacquer by Minwax to let the mahogany shine. Whether you only have a few tools or access to some advanced woodworking machines, you can make some awesome frames. Log in to leave a comment.

Fix This Build That. Quick and Easy Small Bathroom Remodel.

Learn how to cut the segment pieces and glue them up to make a segmented bowl turning blank. The new Rockler Perfect Miter Setup Blocks make it easy to cut the precise angles needed to make the segmented frames. These setup blocks are precisely set to the different miter angles required to cut segmented pieces that make up 4 to 12 sided frames. Dec 13,  · Skylight Frame WiFi Digital Picture Frame Buy The Skylight frame is the one with a difference — it has a matboard which gives it the appearance of a vintage photo frame. Custom trim setup. One way to make narrow moldings with your router is to use a router table and featherboards. But if you don’t have a setup like this, try this other method. Start by routing the desired profile on a wide board. Then make the molding by cutting the shaped edge from the wide board with a .

Watco Stain And Sealer Germany Free Plans For Wood Furniture Table Saw Woodworking Shop 65 Total Tools Woodworking Vise 60