%!$ Easy Diy Woodworking Bench Plans For You #!@

kreg-jig-r3-setting-for-2x4-engine Don Foley said:. Share Another interesting fact is that Kreg tools are inexpensive. Sign in to chat! Hi Deva, Your pocket holes will work just fine as you have them. Sorry for not clarifying that above.

I can't find the actual distance between the R3 holes -- I have an K4. Kreg rep answered your question about hole spacing.

As for using glue; unless you plan on dissembling your project, I would absolutely use wood glue. I always glue my joints, finding one of the big advantages to the pocket holes is not having to leave ther pieces clamped, rather using the pocket holes to secure the pieces as the glue dries.

Ok thanks guys I was getting a lil worried and about to start the project over tomorrow. Reach this article and watch this video to learn more.

OK Kreg Rep, I fully understand why it is not necessary to use glue when assembling a project using Kreg pocket hole screws, but why it is not recommended remains a mystery. Oh yeah, a mystery not answered in the article or video referenced in your post. Tests have shown using wood glue typically creates joints that are sometimes stronger then the wood itself, so why not add glue to the Kreg joint? I also realize the typical Kreg joint is a butt joint using face grain of one piece and end grain of another, an inherently weak joint if built using wood glue alone.

But adding wood glue to the benefits provided by the pocket holes can only increase the strength of the joint. You are correct, Don. However, we don't recommend that customers obtain glue because it is not necessary.

But if you have some on hand or would like the added strength, then it is a fine idea. Sorry for not clarifying that above. Don Foley said:. Don I am totally in agreement as that is pure foolish to short come your project of some glue as that is then a joint that will withstand stress and damage from time as it gets it share of stress as time goes on like the wood fibers will be come more splintery as time ages that wood.

Time will weaken wood fibers and if it gets weak at the joint your project becomes weak. Glue in the joint will hold the wood fibers into a tight bond with each other until the joint is broken apart and not split out and crack apart from the screws that hold it. I would hate to think that a person would not want to build a project that is the strongest as possible when it does not take a lot of extra time and glue is not that expensive.

It is a whole lot less expensive than having a failure in a joint. That is almost as bad as saying you do not have to weld steel plates to a horizontal surface as he weight of the steel will keep it from moving.

I know for certain that I would not build a project with out glue unless it is meant to be taken apart and if the be the case I am not sure I would use screw joinery in the parts that had to be disassembled.

Mechanical fasteners normally crush the wood fibers and then later will work loose from the movement of both mechanical stresses from use or movement from both use and the moisture content changes. That alone will make a loose joint. This will lighten up your loved ones. Another interesting fact is that Kreg tools are inexpensive. The tools combined with the labour that you provide to set it up will not cost you more than How To Set Up Kreg Jig For 2x4 Engine a hundred dollars.

More than that since it is so easy to set up, you can build an item of furniture or fix it in no time, and spend quality time with your family and friends. With all these different advantageous features that Kreg jig offers it is tough to live without investing in it.

Yes, guys! Kreg jig K4 and K5 are similar models. Use the graphic at the bottom of the chart to see which joint you have, and follow the directions for finding the correct box containing the right jig setting and screw length. In the same box you will find the screw length. Be sure to test board combinations that you are not familiar with. Use this calculator to determine the settings you need for your Kreg Jig and drill bit.

It will also tell you what length screw works best for your wood thicknesses. Make sure to choose the correct joint type for your joint.

Jig Tool Home Depot Logo Kreg Jig K5 Manual Quiz 10 Table Saw Blade Lowes 12 Psi Lathe Chuck Yang