%!$ Easy Diy Woodworking Bench Plans For You #!@

kreg-hole-spacing-zone Liu, H. Get the materials, woodworking tools, and free woodworking spxcing here. If so, on the kreg hole spacing zone I'd add glue near the center of panel, but not at the ends. The fracture zone produced by the water-medium uncoupled charging is greater than that of the coupling charging. Need more small woodworking projects?

Add to Wish List. More Details. View Full Details. Compare With Quick View Item Quick View Item Reviews 4. Write a Review.

Learn More. Customer Care Talk to a friendly customer care representative to help with your purchase. Talk to an Expert Get advice on the latest products and help with your projects.

Sign Up. Connect With Woodcraft. For the tabletop I'll be alternating the 2 x 8's with the 2 x 10s 5 pieces total What should the spacing be for the pocket holes on the longer pieces? Share Tweet Facebook. Views: As a general rule when gluing panels, we recommend a screw about 2" from each end, and then screws spaced every 6" to 8" along the rest of the board length. You can put screws just in one side of each joint. I'd probably follow the same spacing for adding the breadboard ends.

One thing to note: I'm not sure if you're gluing boards together or not. If so, on the breadboards I'd add glue near the center of panel, but not at the ends. That's because the boards in the main part of the panel will expand and contract in width some due to seasonal humidity changes. The breadboard ends, though, won't expand and contract in length. So, by just screwing on the breadboard ends or by gluing them just at the center and using only screws on the rest, the wood movement wont cause cracks, splits, etc.

The breadboard term comes from the original construction. Bread boards were traditionally built with Kreg Foreman Semi Automatic Pocket Hole Machine Zone boards at the end positioned 90 degrees to the rest of the panel.

That way it was easy to cut holes for carrying handles, etc. So, today when we build a table top that way, it gets referred to as a breadboard-style top, or a top with breadboard ends. Forgot to say, the breadboard ends also helped to keep the panel flat and still do.

With a breadboard that got hot, moist bread placed on it, there was a tendency for the panel to bow. The breadboard ends, running crossways, help keep the panel flat. That's not as big Kreg Hole Spacing Guide of a deal with the table top or bench top, since it will be attached to the base.

In these applications, a breadboard end is more of an aesthetic choice. Thank you for all that. I love hearing how something became what it is. If you have any other questions, be sure to contact Technical Support at or technicalsupport kregtool. They are very knowledgeable and will be more than happy to help.

The Kreg 2x4 Workbench one of their on-line plans shows using two pocket holes on the 2x4's. I can't find the actual distance between the R3 holes -- I have an K4. Kreg rep answered your question about hole spacing. As for using glue; unless you plan on dissembling your project, I would absolutely use wood glue.

I always glue my joints, finding one of the big advantages to the pocket holes is not having to leave ther pieces clamped, rather using the pocket holes to secure the pieces as the glue dries. Ok thanks guys I was getting a lil worried and about to start the project over tomorrow. Reach this article and watch this video to learn more. OK Kreg Rep, I fully understand why it is not necessary Kreg Hole Spacing 2020 to use glue when assembling a project using Kreg pocket hole screws, but why it is not recommended remains a mystery.

Oh yeah, a mystery not answered in the article or video referenced in your post. Tests have shown using wood glue typically creates joints that are sometimes stronger then the wood itself, so why not add glue to the Kreg joint? I also realize the typical Kreg joint is a butt joint using face grain of one piece and end grain of another, an inherently weak joint if built using wood glue alone.

But adding wood glue to the benefits provided by the pocket holes can only increase the strength of the joint. You are correct, Don. However, we don't recommend that customers obtain glue because it is not necessary. But if you have some on hand or would like the added strength, then it is a fine idea. Sorry for not clarifying that above. Don Foley said:. Don I am totally in agreement as that is pure foolish to short come your project of some glue as that is then a joint that will withstand stress and damage from time as it gets it share of stress as time goes on like the wood fibers will be come more splintery as time ages that wood.

Time will weaken wood fibers and if it gets weak at the joint your project becomes weak. Glue in the joint will hold the wood fibers into a tight bond with each other until the joint is broken apart and not split out and crack apart from the screws that hold it. I would hate to think that a person would not want to build a project that is the strongest as possible when it does not take a lot of extra time and glue is not that expensive.

It is a whole lot less expensive than having a failure in a joint. That is almost as bad as saying you do not have to weld steel plates to a horizontal surface as he weight of the steel will keep it from moving.

Used Cnc Router Machine 4x8 Us Kreg Pocket Hole Screws Drill In Ford F150 Bed Fasteners Co