%!$ Easy Diy Woodworking Bench Plans For You #!@

Changing the blade on a bandsaw can be a real pain in the Wazoo. Most of us will use the wrong blade for a job just because it takes so long to change to the right blade.

Open the wheel covers. Remove the blade guard images one, two, three. The saw is Chinese made so everything is metric. Most machine screws involved in changing the blade have 10mm hex heads or are thumb screws. The table pin is a press fit so pull it out with a pair of pliers.

Set aside. From the back of the saw, loosen the blade tension by lifting the horizontal lever image five to position shown image six. Standing at the front of the saw, grip the blade at the left and right of the wheel image one. Pull the blade towards you off the wheels image two.

You need to clear the blade guard on the left of the saw and you need to clear the metal bracket under the table below the lower blade guides.

Slide the blade out the slot image three. If this were a video, it would be easier to show than to explain with pictures. You should. Hold the blade in both hands.

Twist your left wrist down and your right wrist up. This will cause the blade to begin to fold in on itself. Continue to twist your wrists Jet 14 Bandsaw Guide Blocks 3d and bring your arms toward your center from your elbows. The blade should continue to naturally fold inward into the small loop shown in the last two images.

The end result is a smooth tire with no sawdust clinging to it. Putting on a new blade, even if it is the same size as the blade just removed, is a little more involved than just shifting these instructions into reverse. Unfold the new coiled blade.

But in reality, when I uncoil a new blade, I grip one of the coils an outer ring and then flick the blade away from me.

It springs open like magic! Once open, hold the blade with the teeth facing you. The teeth in your right hand should be facing jet 14 bandsaw guide blocks jack the hook and point of each tooth are pointing down.

Correct it by pressing the teeth inwards. The top of the blade should curve towards you. Keep pressing until the entire blade flips around and the teeth are facing back away from you. Now, turn the blade around and slide it through the table slot image five. Fit the blade around the wheels. Slide it between the upper and lower blade guides and the blade guard on the left hand side by the switch jet 14 bandsaw guide blocks jack six through nine.

Loosen and back off the upper and lower blade guides and bearings. Go around to the back of the saw and flip the tensioning lever down to tighten jet 14 bandsaw guide blocks jack blade on the wheels. Before centering the blade, make sure it does not rub against any of the blade guides or guide bearings. The blade should spin freely.

Face the upper wheel as shown in the 3rd image. The 3rd image shows the blade too far left on the wheel. Using the knob to the left of the tensioning spring 1st jet 14 bandsaw guide blocks jackloosen the wing nut and turn the knob clockwise or counterclockwise while rotating the wheels and center the blade on the wheel 4th image.

When centering the blade on the upper wheel, you may notice that the blade is not centered on the lower wheel. That is, they are not aligned vertically with each other. They are not on the same plane.

So it may be necessary to jet 14 bandsaw guide blocks jack the blade slightly forward left of center.

We want to be Democratic after jet 14 bandsaw guide blocks jack. All guide blocks and bearings should still be away from the blade. Tighten the thumbscrew. Rotate the blade —by hand. The blade will wobble slightly most blade welds are not straight and so should brush the bearing slightly as it rotates around the wheels.

Adjust as needed. Bring the guide blocks in towards the blade. Temporarily tighten the thumbscrews. Now, loosen the side thumbscrew image three, lower screw and adjust the blocks knurled nut so that they are barely behind to the right of the tooth gullets.

Tighten that jet 14 bandsaw guide blocks jack. Loosen the block thumbscrews again. Tighten the thumbscrews again. Things will move, so readjust as needed. OK, now close all doors, re-insert the throat plate jet 14 bandsaw guide blocks jack the table pin.

Plug in the saw. With your safety glasses on, turn on the saw. Watch the blade; see if it drifts against the bearings or drifts away from the bearings. Turn the blade adjustment knob as needed to position the blade back to where it just brushes the bearing and the gullets clear the guide blocks. Great tutorial! I've got an 18" Jet, and you're absolutely right about using the wrong blade out of laziness.

I need to get more proficient in changing my blade. Thanks for posting this! I don't always need it, but I've used a spring clamp to hold the blade on the top wheel when installing. Introduction: Changing Blades on the 14" Bandsaw. More by the author:. About: SLO MakerSpace offers tools, training, and consultation services that enable community members to experiment with and master a wide variety of Maker skills.

Remove, fold and store the blade. Looking at the pictures: Easy Peazy, right? Use a twist tie or piece of masking tape to secure the blade. After centering, re-tighten the wing nut image two. Turn off the saw. Jet 14 bandsaw guide blocks jack the front blade guard. You're done. Did you make this project?

Share it with us! I Made It! Incredible Wooden Spirals by rschoenm in Woodworking. Telescope Setting Circles by instgct in Jet 14 Bandsaw Guide Blocks Me Science. Reply Upvote.