Diy Wood Vent Hood 3d,Marking Knife Turning Kit Quinn,Pin Gauge Set Box - And More
Hey there!!! As much as I love getting my house festive for Christmas, I also love a good quick and easy update around the holidays!
We have our family which resembles a small army of mostly children over to our home for Christmas Eve. I look forward to it every year and love that it has become a tradition.
My vent hood update was the project I wanted finished most! If you follow us on Periscope, you may have seen the sneak peek of this project and my newly painted cabinets! Think FaceTime or Skype! You can find us shanty2chic on the Periscope App! We would love for you to join us! The color I had them painted is Anonymous by Sherwin Williams.
I am not sharing measurements on this project because everyones space is different. This tutorial is meant as a go-by so that you can create something similar in your own home. Then I drew a diy wood vent hood 3d line down the center point of the piece. I made a 45 degree cut on my first board. All of the angle cuts for this piece are 45 degrees. You can see in the picture above that I slid my miter handle bottom handle over to the left to the 45 degree mark.
I made the first two boards split the corner, so this board will sit on the right side of the bottom corner. I marked where this piece needed to be cut and made another 45 degree cut. When I made it to the top corners, I was not able to split the corners with 2 boards. I chose Varathane Early American Stain. You can find this brand at Home Depot.
I applied one coat diy wood vent hood 3d stain using a clean cloth. I let the stain sit for about 5 minutes, then I wiped it with another clean cloth. I used my Corner Cat sander to distress the entire piece. I used grit paper for this and distressed it a TON! I removed the cabinet doors and hinges first.
So the inside of the cabinet is exposed and I left the face frame as-is. Now to build the mantel! This is an important thing in building. I was able to use some plywood scrap to build the mantel. This saved money and a trip to the hardware store. So, here are the pieces for the mantel. So, now the mantel should look like this. I also drove screws from the inside of diy wood vent hood 3d cabinet box into diy wood vent hood 3d sides of the mantel for extra support.
Once the mantel was attached, I used my 18 gauge nailer and wood glue to attach the bottom of the mantel. Now to pretty it up! This will cover the ugly nail holes from attaching the bottom piece of the mantel. Measure and cut this to fit. I like to do the front pieces first, then the sides. The sides are easy to sure up because the have a square cut on one end! I filled my nail holes with wood filler and gave it one coat of the same Early American stain and distressed it all over.
I could NOT be happier with the results. It adds so much to my kitchen and because the kitchen is open to the rest of my home, it really adds so much to my home! Love the color of your cabinets. We just purchased a new house and looking to use similar colors.
They are beautiful!! I absolutely love this project and plan on doing this in my new home. My new home is still under construction and I wanted my range hood wood wrapped, but the builder would not do it with the brand of hood I chose for some reason.
So, because I do not have an existing cabinet like you had, I will have to build this entirely from scratch. My question is, how do I mount this? Would I take plywood for the side panels and attach them to the cabinets on either side of the hood or do this and attach to studs in the back wall? Your time and input is appreciated! Hey diy wood vent hood 3d I was wondering the same! How does this work with cooking.
My husband says that it will absorb the cooking grease and get ugly. How does it hold up. It looks like you have an above the range ventilation hood above your cook-top and inside the cabinet.
Did this stand alone at one time? Did you build the cabinet around it? We are currently building a home and looking at ventilation hoods. Love the wooden vent hood! I have been waiting for the instructions on this project. Would putting the plywood on hinges be a problem? Not sure if placing hinges on just one side would be enough or if four hinges would be better. Thank you! Love it. You give great instructions.
Diy wood vent hood 3d Pretty. Love your cabinet color too. You have a Beautiful Home!! Notify me of follow-up comments by email. Diy wood vent hood 3d look! What is the tile flooring and wall color in this kitchen, please? Michelle on March 10, at pm. What color of paint do you have on the walls? The cabinet color is sherwin Williams anonymous. FirstLorenzo on December 26, at pm. Kendra Oswald on August 17, at pm.
Jen Hall on May 13, at pm. Shanty2Chic on May 13, at pm. Dara Strickland on March 20, at pm. I risk sounding like a simpleton here, but how do you operate the diy wood vent hood 3d and light now?
Shanty2Chic on March 20, at pm. Eva on September 11, at am. Elizabeth on June 16, at pm. Tammy on February 5, at pm.
Kelly 'Spring' Long on February 1, at pm. Lisa on March 9, at am. Austin Storm on January 30, diy wood vent hood 3d pm. Ashlen on January 12, at am. LA Picker on January 10, at pm. Mary on December 3, at pm. Shanty2Chic on December 3, at pm. Bill McNutt on January 13, at pm.
Beverly Hall Grigsby on December 3, at am. Jamie K on December 3, at am. Facebook Twitter Pinterest.
Fein Vacuum Vs Festool Review Remove File Cabinet Lock Cylinder 10 |
BREAST
26.07.2020 at 23:35:18
BIZNESMEN_2323274
26.07.2020 at 21:45:41
Birol
26.07.2020 at 12:59:22
Scarpion_666
26.07.2020 at 15:24:12