Woodworking Plans Rotating Bookshelf Me,Woodwork And Carpentry Pdf,Different Parts Of A Hand Plane Jump,Large Wood Bowl Blanks Of - Step 3
I built my first bookcase in middle school. A multitiered assemblage of wooden planks laid across stacks of bricks, it was reminiscent of woodworking plans rotating bookshelf me from the early Flintstone Period--and I was proud to have made it myself. Since that masterpiece, I've built 50 or 60 more, most while working as a cabinetmaker for an interior design firm, where I learned the carpentry skills, design guidelines and construction techniques used in the bookcase shown here.
Basically consisting of three plywood boxes fitted with a hardwood face frame, this piece looks built-in because it spans from wall to wall, and is trimmed with molding at the ceiling and floor. With moderate skills and some patience, it wouldn't be hard to make this project fit any space.
On permanent display: mahogany, solid biscuit joints--and a whole lot of class. Two pieces of plywood form each side of the cases. In contrast, the horizontal mahogany apron attached to the front of each shelf overhangs the plywood. The shelves fit into dado joints routed into the case sides. Since the shelves were going to be glued and screwed into the dadoes, they couldn't be adjusted later.
So I measured my books before I decided how tall the shelves should be. As a rule, a woodworking plans rotating bookshelf me with shelves between 7 in. While books generally fit on 8- to 9-in. I chose to attach the wooden face frames--stiles, rails, valance and aprons--to the plywood cases with a biscuit joiner so that fasteners wouldn't mar the mahogany.
But the quickest, easiest approach would be to use a pneumatic finishing nailer--then fill the nail holes with putty. Start by building a base out of 1x or 2x lumber. Set the base into position and check for level right to left and front to back. Fasten it to the wall studs using 3-in. Also drive angled screws through the inside of the base and into the floor. Crosscut the case sides to length, making them 2 in. Then, cut all the shelves to length.
The shelves should be no longer than 36 in. Before proceeding, finish all the plywood pieces. Clamp two opposing case sides edge-to-edge and mark each dado location with a pencil.
Be sure and mark the location of the case tops woodworking plans rotating bookshelf me enough down on the case woodworking plans rotating bookshelf me, so that the tops provide a woodworking plans rotating bookshelf me surface for the valance. Next, clamp a straightedge guide across the two sides. Slowly push the router along the guide, crossing both plywood pieces.
If you plan to use biscuits to attach the face pieces, cut the necessary slots with a biscuit joiner [ 2 ]. For the tall sides, space the slots about 12 to 14 in. Cut three slots into shelves that are 18 in.
I cut slots for No. Since the bookcase has no back, you need to install a wood strip, or hanging rail, to screw each case to the wall. Cut the rail from a 1 x 3 or 1 x 4 to fit between the two case sides.
Position it directly above the case top, and attach it to the case sides woodworking Woodworking Plans Rotating Bookshelf Quote plans rotating bookshelf me glue and screws. Set each assembled case on its base [ 4 ] and use a 4-ft. Next, secure the cases by driving 3-in. Use six strips total: two each at the bottom, center and top of the sides.
Attach the neighboring case, if there is one. Otherwise, clamp a side panel to the plywood spacers, creating 2-in. With the plywood cases installed, cut the mahogany face-frame parts, which include: 2-in.
Before installing each mahogany part, sand it smooth, then apply a finish. Start with the horizontal base rail at the bottom of the bookcase. Woodworking plans rotating bookshelf me the rail against the bottom shelf and mark onto the rail the center of each slot cut into the shelf. Then use the biscuit joiner to cut corresponding slots into the back of the base rail. Apply carpenter's glue to the front edge of the bottom shelf, and the rear of the base rail.
Insert No. Use a rubber mallet to tap the rail tight. Wipe away any excess glue with a cloth. Attach the valance that runs across woodworking plans rotating bookshelf me top of the bookcase the same way.
Note: Its bottom edge aligns flush with the case top. Now install the vertical stiles. Cut slots using the biscuit joiner, apply glue to both surfaces, insert biscuits into the slots and press the stile home.
Use a rubber mallet to tap it tight. Prior to installation, I routed a decorative profile along the bottom edge of each apron to create shadow lines that accentuate the shelves. The aprons are more than decorative, though. They stiffen the shelf to prevent sagging. Trim the top of the bookcase with crown molding [ 8 ] and the bottom with base molding [ 9 ]. Wait 8 to 10 hours for the glue to cure before filling the shelves.
Save this article for later by pinning it. For more ideas, follow Popular Mechanics on Pinterest. Type keyword s to search. Today's Top Stories. The 71 Best Woodworking plans rotating bookshelf me of How to Get Started in Rock Climbing. American Artist. This content is created and maintained by a third party, and imported onto this page to help users provide their email addresses. You may be able to find more information about this and similar content at piano. Advertisement - Continue Reading Below.
More From Projects and Plans.
Kreg Jig Setting For 2x2 Kit How To Build A Toy Rocket Ship 81 |
RAZiNLi_QIZ
04.04.2021 at 20:58:26
KISKA
04.04.2021 at 19:47:28
periligun
04.04.2021 at 12:28:52
lala_ASEF
04.04.2021 at 10:28:14