%!$ Easy Diy Woodworking Bench Plans For You #!@

stanley-sweetheart-block-plane-parts-level Stanley No. /2 Sweetheart™ Low Angle Block Plane | Rockler Woodworking and Hardware

We may receive a commission when you use our affiliate links. However, this does not impact our recommendations. My first Stanley shoulder plane a No. So when the new Stanley Sweet Heart No. Note: This tool is a loaner, so it will go back to Stanley after it has had a workout at Woodworking in America. I took the tool out of its sealed box and checked the sole with a machinist square.

This morning I decided to look at all the shoulder planes in our shop, and compare them to the Stanley. The exception was the Veritas Large Shoulder, stanley sweetheart block plane parts level was dead square.

Most of these planes have performed fairly well, but they all have problems when you try to do persnickety work. You have to massage the position of the cutter to get the results you want. The exceptions being the Veritas, which is always dead on, and my Lie-Nielsen at home, which is also always bang-on.

So I decided to true up the soles of several shoulder planes today and see if it improved their performance. Next Stanley sweetheart block plane parts level took a piece of plywood and set it on my bench in front of the sandpaper. I rested the shoulder plane on the plywood, hung its sole off the edge and stroked it back and forth over the sandpaper.

After about a minute of work I checked my result. The sole was improving. About three minutes later, the sole read dead flat to my stanley sweetheart block plane parts level. Then I sharpened up the A2 iron.

The unbeveled face of the iron was dead flat, which stanley sweetheart block plane parts level always a nice surprise to see. It polished up quickly. I quite like the stanley sweetheart block plane parts level, but I like rhino-horn-style shoulder planes the horn is the proboscis at its toe.

Megan Fitzpatrick reported that the plane had too many sharp arrises. I agreed and knocked them down with some sandpaper.

And actually, after looking at photos of the original No. The No. When you are really bored, check out all my articles Stanley Sweetheart Block Plane Parts Center on WKFineTools. Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, stanley sweetheart block plane parts level have carefully selected these products for their usefulness and quality.

Chris, Did you check the blade protusion at the sides? Should be about 2 mils. By the way, I had to true up the sole of my stanley sweatheart Except for Veritas and LN, I expect this for every plane until the manufactures get the message. The stanley sweetheart block plane parts level is installed and retracted. And the lever cap is under working pressure in that photo. In other words, I agree entirely with David.

Charlesworth goes on at length about how you have to have the blade installed when flattening because the tension created by installing the blade deforms the sole and makes a hump at the mouth. Do you disagree? The Veritas has that funky adjustable knob that sits right where my palm wants to go and the plane is just too top heavy.

The Lie-Nielsen is just plain awkward to hold. Looks like they got it right assuming the quality control is consistent. Some one help answer this question. Why would I want a plane that opened up into a chisel plane, i.

Obviously cost, but is there a more compelling reason? Some how, this does not compute. By Christopher Schwarz. Stanley Sweet Heart No.

The sole was out of truth. Probably by a couple thousandths of an inch. Maybe more. Chris is the former editor of Popular Woodworking Magazine.

He continues to blog and publish woodworking books at Lost Art Press. He's a hand-tool enthusiast though he uses power tools, too. Manuel Cardoso-Lopes September 8, Cheers, Manuel.

Gordon Conrad August 24, Christopher Schwarz August 24, Carl Stammerjohn August 24, Stephen August 23, Dusty Lenscap August 23, I had the same problem with my Clifton The bottom was not quite flat. But a little elbow grease and all was well. Other than that, its been a good hand plane.

TSJones99 August 23, All rights reserved Privacy Policy Terms of Use. Start typing and press Enter to search. American Woodworker Blog.

Type 2 Type 12 First of “Sweetheart” types. Type 3 Type 13 “Stanley” appears on lever cap. Type 4 Type 14 “Made in USA” appears cast into Type 5 Lateral adjustment lever appears. bed. Type 6 Type 15 Last of “Sweetheart” www.- Size: 63KB. Mar 26,  · A precision ground cast iron base (/8" W x /2" L) ensures smooth and accurate planing. Frog and base are cast as one piece to greatly reduce chatter and /5(64). SWK (Type 1) Stanley Stanley Block Plane Parts. (Type 1) Stanley Bailey Smoothing Bench Plane Parts. L (Type 1) Stanley Bailey Smoothing Bench Pl Parts. (Type 1) Stanley Bailey Prof. Smoothing Pl Parts. L (Type 1) Stanley Bailey Prof. Smoothing Pl www.- g: stanley sweetheart.

Woodcrafters Woodworking Supplies 82 Parts Of Cnc Router Machine 40 Black Locker Cabinet Limited Circle Jig 70