%!$ Easy Diy Woodworking Bench Plans For You #!@

portable-dust-collector-harbor-freight-of Harbor Freight Dust Collector Review

This is going to be a long picture and video filled post. Hopefully a one stop shop for those who want to do the same thing for their woodshop dust collection. This creates a negative pressure inside which is not a problem for me. After asking a few questions on the LumberJocks forum and reading a handy little DIY approach to the same thingI decided to use the bag ring to make a Thien baffle and mount the motor directly on top. I used two layers of MDF to create the bottom baffle and 2 layers for the motor mount on the top of the ring.

Hopefully these pictures can better describe whats going on. Videos at the end. Here is the bottom baffle being cut. I originally messed up right here. I had the air intake lined up with the two lines below where the slot starts. That was wrong. Where the air intake starts is where the platform should start.

The slot cutout should end right Portable Dust Collector Harbor Freight Price before the air intake. Luckily all I had to do was rotate the MDF 90 degrees counter clockwise. I went with two layers of MDF on bottom because I felt that the groove for the can and ring were too portable dust collector harbor freight of and would result in a very weak piece of MDF. On the bottom layer seen here I removed a large section of the baffle area and left a pie shape to help support the weight on the piece above.

The two bottom pieces are stacked together. In relation to the slot, the air will be coming in from where my left hand is, not my right hand as I originally had it.

It was clogging before I made the change. Test fit. I was a little skeptic about leaving the cone shaped inner ring. The author of the writeup I read said he left it. So thats what I did. Time to cut some more MDF. The top has to portable dust collector harbor freight of 2 layers as well. This is the top-most layer. Where my hand is located is the exhaust for the blower. An elevated mounting platform is needed to clear this rectangular flange.

The layer directly above the ring is pretty straight forward. This is a rough assembly. Time to put it in location. Initial Portable Dust Collector Harbor Freight install. I did not have any DC hose so I tested it with some flexible drain hose. This is when I realized the improper position of the air intake relative to the baffle slot. Easy fix like I said, just rotate the bottom two pieces.

I had to think of a way to easily elevate portable dust collector harbor freight of whole unit and remove the can for emptying. This is what I came up with.

Just a scrap wood frame to straddle the can on 3 sides. It is sized so that the height of the rails are slightly shorter than the bottom baffle. Testing out how easy it is to remove the can. It was a little cumbersome at first but after adding handles it is super easy to remove the can. Because I purchased the unit with the intentions of building this setup I had a lot of extra parts that I will never use.

This is a budget conscious project. I wont get too much into this. I ended up removing the switch I made in video 5 and replaced portable dust collector harbor freight of with two switches that I will show later. The original idea. Using extension cord to make a corded remote switch. I changed this to 2 dedicated hardwire corded remote switches. With the unit done I started on plumbing the shop.

First thing was to come up with some blast portable dust collector harbor freight of. I ended up making them with half of a coupling on one side and portable dust collector harbor freight of piece of pipe on the other. This gave me a male and female end for the blast gate which will allow me to place it into any junction with a connection for running pipe on the other end.

Super simple, super easy, they work great. This picture shows each piece before assembly. I glued the appropriate pipe portable Portable Dust Collector Harbor Freight Website dust collector harbor freight of to the center of each piece of ply. Drilled a hole in the middle after the glue cured and used a flush trim bit in Portable Dust Collector Harbor Freight Solution my router table to clean up the inside. This is what it looks like today. I rotated both the base and ring this time so that the Y fitting is close to the wall.

Lets start with the top side of the Y. I have the pipe running right below the window sill going into the corner. My original plan was to have 2 45 degree fittings to make a gradual turn around the corner.

I decided to go with another Y and This allowed me to add a pipe and blast gate going portable dust collector harbor freight of the floor. The pipe going to the right goes to the new miter saw station. Just sweep the floor into the corner and watch the magic happen : Here is also a good look at the completed blast gates. They work great. From the corner we come into a 45 fitting, blast gate, and then back to a cardboard enclosure that collects the miter saw dust.

It works great as well. Heres a good shot of the miter saw blast gate and where the first wired remote switch is located. Back at the DC we can follow the bottom side of the initial Y. The hose runs behind the can. I can easily remove the first hose and place it on my DW planer that is sitting above. After the blast gate it goes behind my workbench to the table saw.

Coming around the work bench and connecting to a 45 to my table saw station. Here is the lower part of my table saw station.

A blast gate for the table saw and one for the future router upgrade. I am thrilled with this setup :. Here is the second corded remote switch for the DC. They are wired direct, not via a 3 way switch. Simply lift the assembly up about a half inch and slide the pine spacer in to support it. One on each side. And here is the exhaust hose. I cut a hole in my Plexiglas window filler. Its not perfect. Nothing a little HVAC tape cant handle.

Just let it lay on the bottom of the pipe. But put it through every bit of the pipe. Then ground the ends of it. The reason being, sawdust running through that pipe builds up static electricity.

And suspended fine sawdust makes a fine explosive! There HAVE been explosions and fires caused by shops running pvc for dust collection and not putting the grounded copper wire in there. Yes it can create static. But all the research concludes that it is not dangerous in a home shop.

Uncomfortable maybe, but not dangerous. I bet a metal portable dust collector harbor freight of ring would do the trick too. The extra HF mobile base parts I did build out so that my unit is mobile. After watching some online videos of these things in action, I guess-timated an angle for the debris swirl inside the top hat, and therefore the placement of the solid part of the baffle.

Who knows if I got the placement correct, but I did notice that on my first test, where I sucked up the contents of my portable dust collector harbor freight of Fein Vac separator, there was a pretty short, initial puff of noticeable superfine dust that was freely exhausted.

How did yours work out?

Get everything you need to connect your 4 in. dust collector to your shop equipment. This two-hose dust collector accessory kit lets you power up to two machines at the same time. Everything you need to set up a dust collector in your woodshop; Two sets of hoses and blast gates let you collect dust from multiple machines/5(). For any difficulty using this site with a screen reader or because of a disability, please contact us at or cs@- . For California consumers: more information about our privacy - information about our privacy practices. May 30,  · Harbor Freight 2HP Dust Collector, Model $ **Coupons and discounts are frequently available for all Harbor Freight tools, and shipping is a .

Triton Tra001 Price Year Woodworking Shop Table Saw Japanese Crosscut Timber Saw Review