%!$ Easy Diy Woodworking Bench Plans For You #!@

mounting-jet-air-filtration-year Comment Post Cancel. As a result, I got the eyes mounting jet air filtration year an inch closer together on one end. Leave a comment - we'd love to hear from you! I'm just going to add that a shop vac that can accommodate a bag most Shop-Vac brand and many Ridgid units can do a lot to prevent dust from becoming airborne. Thanks again, Brian. Posts Latest Activity Photos. I know the DeWalt and routers have nifty hose fittings on their plunge bases.

My shop is 12' x 18', with the 18' on the opposite side of the wall for the stairs. Dust does tend to creep to the other rest of the shared half of the basement, especially when working with MDF. I use a table saw, miter saw, routers and sanders and currently have no other dust collection systems.

Where should I place the Jet? The directions are limited and suggest avoiding corners. This will create a pretty good draft and some noise for others in the basement.

The air would be pushed towards the area I want to protect. The biggest problem that I see with this choice is the Jet would be pulling air from the entire basement which could possibly reduce the effectiveness. To add another twist, the ceiling height is only 7'5" and the Jet is 12" high.

I'm tall enough to hit my head but I need clearance for moving stock and not block light. Tags: None. Odd you should ask this just now, because I'm wondering the same thing myself as I iron out the final details of the power plan for my new shop building. Most of the installations I have seen in magazine photos or on the Internet have the filter hanging more or less out in the middle of the room, perhaps cheated toward the area where the bulk of the dust is produced. That seems to make sense, and so I was planning to locate a ceiling outlet at the appropriate location.

In my case that was centered across one direction of the shop, but a couple feet off center the other way. If the object is to filter ALL the air in the shop, this seems to make even more sense than a central location. So, further investigation is needed, something I've not yet had time to do.

If I find anything more, I'll post it here. Last edited by LarryG ; , PM. Reason: clarity. Comment Post Cancel. I have hung the cleaner from the ceiling with the intake facing my table saw and router. The intake is about four feet from the out-feed side of the saw and about seven feet from the floor.

I have had the unit in place for about two years. This powerful unit is perfect for the smaller home shop. Simply hang it from the ceiling turn it on and it will clear the room of those fine dust particles. This unit was the first in the industry with remote control, timer and three speeds which have quickly become the industry standard. JET warrants every product it sells. If one of our tools needs service or repair, one of our Authorized Service Centers located throughout the United States can give you quick service.

As you work your way higher and higher, always keep an eye on the chains opposite you. If one slips off, reattach it before proceeding. The other ladder was no longer cutting it at this point. I needed something to lean on while lifting the weight near ceiling level, so I switched to a taller ladder. Finally, once you reach the desired height, cut off the excess chain. Or you can just double up the S-hooks by hooking the ones from above through the eyes on the air filtration unit.

And hooking the ones on the filter unit through the eyes on the ceiling. At many times during the process, the weight will temporarily be supported by only three corners. Once you have the unit positioned where you want it, however, check that the load is distributed among all four. If one has slack, adjust an eye screw or hook to snug it up.

And there you go — one shop air filtration system suspended from the ceiling. If and when you ever need to take it down again, simply reverse the process. Your friends might wonder how you managed to do it all by yourself. Steve made his first woodworking project at age 9 in and whittled his first wooden chain at He was also a consumer electronics repair tech and shop owner for a little over 20 years, until his impending obsolescence became impossible to ignore.

Since then, Steve has focused passionately on manipulating his wood Don't judge him. A clever solution to a weighty problem, Steve. Thank you, Phil, on both counts.

Carving Kit Michaels Jr Hand Held Circular Saw For Sale Free