%!$ Easy Diy Woodworking Bench Plans For You #!@

mastercraft-belt-and-disc-sander-parts-malaysia Craftsman 4 X 36" Belt / Disc Sander | | www.-

Table Of Contents. Quick Links. Parts Missing or Damaged? Toll-Free Helpline: Table of Contents. Previous Page. Next Page. Sander MasterCraft Instruction Manual 3 x 21" belt sander 11 pages. Mastercraft belt and disc sander parts malaysia to observe any of the following instructions could result in severe personal injury to tool user and bystanders or cause damage to tool and property! Page 5: Before You Start Operating Instructions Before You Start — Electrical In the event of a malfunction or short circuit, grounding provides the path of least resistance for electrical current and reduces the risk of electric shock for the operator.

This tool is equipped with an electric cord that has an equipment grounding conductor and a grounding plug. Repair or replace damaged or worn cords immediately. Be sure your extension cord mastercraft belt and disc sander parts malaysia properly wired and in good condition.

Do not use damaged extension cords. Carefully remove all parts from the shipping carton. Page 8 Installation of Sanding Disc and Guard 1. Peel backing away from sanding disc. Locate table support and 3 hex head screws, washers and locking washers in loose parts bag. Place table top-down on a flat surface.

Position table support against table bottom, aligning holes on support with pre-drilled holes in table. Page 10 Installation of Belt-Sander work support 1. Locate work support and hex screw, washer and locking washer. Hold work support in position and fasten as shown. Do not overtighten. Turn the power off and remove the plug from the outlet before changing the accessories.

Removal: 1. Slide tension lever to the right to release the belt tension. Slide the used sanding belt off of the rotational mechanism. Installation: 1. Page 12 To properly track the sanding belt: 1. Plug in the sander. Turn power switch ON, then immediately OFF, noting whether the belt tends to slide off its track, and to which side front or back of the sander.

If the sanding disc did not tend to either side, mastercraft belt and disc sander parts malaysia is tracking properly. Page 13 Sanding operations are inherently dusty. Depending on operator needs and the workpiece, the work-support can be used with either the horizontal or vertical position.

Page 15 Surface Sanding on the Sanding Belt When sanding flat, broad surfaces on the belt sander, hold the workpiece firmly but lightly onto the surface of the belt and against the work support work restkeeping fingers away from the sanding belt. Page 16 Sanding Disc Station - Sanding Outside Curves Always sand outside curves using the sanding disc and moving the workpiece from the left side of centre, as shown.

Keep the curve pressed firmly against the sanding disc, moving the work evenly from the left side of the sanding disc.

DO NOT attempt to repair or maintain the electrical components of the motor. Take the sander to a qualified service technician for mastercraft belt and disc sander parts malaysia type of maintenance. Ensure sanding rub off belt or discs. Page 19 Motor overheats. Motor overloaded. Reduce load on motor 2.

Utilize an extension cord of appropriate gauge and length or plug tool directly into outlet. Motor stalls resulting in 1. Page 20 Parts Schematic Print page 1 Print document 22 pages. Cancel Delete. Sign In OR. Don't have an account? Sign up! Restore password.

Upload from disk. Upload from URL.

Craftsman belt & disc sanders have the powerful motors and rugged components that you need to complete any sanding project. Although Craftsman belt & disc sanders rarely break down, you can never tell when parts will wear out or a failure will eventually www.- g: malaysia. Feb 14,  · Black Rubber Drive BELT Mastercraft Belt & Disc Sander Model N www.- : Home & Kitchen Small Appliance Parts & Accessories Currently unavailable. We don't know when or if this item will be back in stock. Share. VIDEOS ° VIEW IMAGES Black Rubber Drive BELT Mastercraft Belt & Disc Sander Model N Heritage Parts is a trusted distributor of Mastercraft replacement parts. With same day shipping, real time inventory, and always % Genuine OEM parts, Heritage is your one stop destination for commercial kitchen replacement parts. Right Part, Right Time, Every Time!

Slimline Ltr 17 Drawer Slides Used Woodworking Tools For Sale In Philippines Stock Woodwork Projects Beginners 4k Wood Shop Vacuum System Model