%!$ Easy Diy Woodworking Bench Plans For You #!@

craftsman-9-radial-arm-saw-manual-review Page 6 The one common complaint on the Delta saw was that the saw blade was made of steel, not carbide tipped like other brands. Login to Add to Toolbox. I The craftmsan number will be found on a plate attached to the base. Figure 3. Classified Ads Vintage Machinery Store.

Next Page. Summary of Contents for Craftsman Page 1 Page 2 This warranty gives you specific which vary from state to state.

Page 3: Major Hazards Read and follow all safety information and instructions. Major Hazards Three major hazards are associated with using the radial arm saw for ripping, They are ouffeed zone hazard, kickback, and wrong way feed. When a workpiece kicks back, it could hit hard enough to cause internal organ injury, Page 5: Safety Instructions 4. Keep floors clean and flee of sawdust, wax and other slippery materials. Keep work area well lighted and unclut- tered, 6.

Use saw only in dry area. Do not use in wet or damp areas. Dust Mask Ear Proleclors Page 6 Keep saw table clean. Store items away from saw. Do not climb on saw or stand on saw table to reach items because saw can tip over. Page 7 6o Do not turn saw on and off in rapid sequence because blade can loosen. Blade should stop within 15 seconds after saw is switched off.

If blade takes longer, the saw Craftsman 9 Radial Arm Saw Manual Car needs repair. Contact Sears Service Center. Safety blade nut because Also See for Craftsman Related Manuals for Craftsman Saw Craftsman Summary of Contents for Craftsman Contact a Sears Service Center for repair. Page 3 AttachingElevating Handwheel Installingthe Yoke Assembly Removing the Blade AttachingTable Supports Setting the Arm Lock Knob Setting the Yoke Clamp Setting the Bevel Lock Lever Tightening the Arm and Column Adjustingthe Column Tube Levelingthe Table Supports Page 4 The purpose of safety symbols is to attract your attention to possible dangers.

The safety symbols, and the explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger. The Instructions or warnings they give ere Used Craftsman Radial Arm Saw Review not substitutes for proper accident prevention measures. Craftsman replacement parts. Use of any other Get in the habit of checking - before turning on the parts may create a hazard or damage product.

Firmly boltthe saw to the leg guard and anti-kickback pawls. Test the pawls to stand to keep the saw from tipping,walking, or make sure they would stop kickbackif it started. It shouldbe connected to a power supply that Is volts, 60 Hz, AC only normal household current. It should be connected to a volt power supply only If It has been reset according to the Instructions in this manual. Your radial saw has been set up at the factoryto operate efficientlyon a V AC single voltagecircuit.

However, if heavy duty operation is required,the circuitsare overloaded, or the circuitis low voltage, have a qualified electdcian change the voltage on the main power system to a V AC voltage circuit. Depth of Cut at 90" Depth of Cut at 45" 2. Blade Bevel Angle 0" - 90" Table Size 40 x Radial Arm Swing Range 50" Page 11 Throw-Back Resin Saw throwing back a workpiece similar to kickback.

A sticky, sap-based substance. Through Sawing Rip Cut " In a radial saw, a cut made with the blade parallel to AnyCutting operation where the blade extends completely through the workpieca. Page 12 Check a ll loose parts from the box with the Craftsman Radial Arm Saw Review Pdf list below. Use the instructions on the followingpages to assemble.

Allfasteners are shown actual size. Saw Assembly Page 13 Check a ll loose parts from the box with the list below. Use the Instructions on the followingpages to assemble. All fasteners are shown actual size. Saw Assembly not shown Page 14 Check all loose parts from the box with the list below.

All fasteners are shownactual size. Leg Stand Table Support A. Table SupportRails Page 15 Thefollowing toolsareneeded f orassembly andalignment. They arenotincluded w iththissaw. Page 18 motor, blade, and blade guard and can be pivoted with all operating features and safety requirementsof so the blade faces right,front, or left.

It is located below the handle. See Figure 9B. See Figures 9A-9D. Contained in two carriage covers, one on each side of the arm. See Figure 9C. See Figure 9D. When you remove the saw and hardware insert levelingfeet intothe bottom of the legs.

See Figure Ignodngthis precaution to keep the saw from tipping,walking,or sliding. Install the yoke assembly from the front of the arm. Remove the blade and blade guard assembly during The table supportsare a base for the three wooden table sectionsand fence. The bevel lock lever is preset at the factory but may need readjustmentafter shippingor extended use.

Check for overtightnessor looseness and make any neces- sary adjustmentsas follows: The bevel lock lever is locatedon the frontof the yoke See Figures 20A - 20D.

If you can movethe arm inner column tube is snug in the housingand to remove any looseness. Press the arm to the side. If there is play between the column support and the column tube, it needs to be adjusted.

See Figure 20B. If not, adjustthe table See Figures 22,4 and 22B. Use this procedure to installthe fixed fronttable. The top of the table has counterboredholes, preddlled from the top, around the center to attach the table. In the center are a counterbored hole and a small hole, which is not counterbored. They are used for raising or loweringthe center of the table until it is level.

If there are any high or low areas on the front table, they should be removed by adjustingthe leveling The placement of the tables and fence may need to screws in the center holes on the front table. Place the inner bladewasher, saw blade, outer blade washer, and blade nut on the blade arbor. See Figure26A.

The Woodworker Magazine News Furniture Veneers Uk Tracking