%!$ Easy Diy Woodworking Bench Plans For You #!@

4-pocket-hole-jig-guide Founded inWolfcraft has its offices in over 50countries. Set your drill to its slowest speed and drive the screws in until they draw the boards together and stop. For joining boards on their edges, you can hold them together with this right angle clamp. Pocket screws 4 pocket hole jig guide a special flat head that seats firmly on the shoulder left in the pocket hole by the stepped drill bit. You can easily clamp it over the iron bench vice of your workshop. Bole, you should always seek the Pocket Hole Jig that has its accessories 4 pocket hole jig guide body built of quality materials, this will make your jig last for many uses. You can learn about how I handle information I collect by viewing my Privacy Policy.

Add to Cart. Notify me when this is back in stock. We take customer satisfaction seriously. Proposition The perfect choice for DIYers. Work smarter, not harder. Plans for your next project. Powered by. Product Quality. Ease of Use. Write A Review.

Ask A Question. What is your Building Skill Level? How many Projects do you complete in a Year? How would you rate the Quality of your product? How would you rate the Ease of Use of your product? Would you Recommend this Product? You are connected as. Connect with:. Thank you for posting a review! We value your input. Share your review so everyone else can enjoy it too. Your review was sent successfully and is now waiting for our staff to publish it.

Thank you for posting a question! Please click on the link in the confirmation email we just sent you to submit your question. Your question will appear on the site once someone answers it.

Be careful to not apply pressure that pushes the bit out of this alignment, as that can be hard on the bit and the bit-guide. If you attach a shop vac on the jig, your wood chips will do a pretty good job of staying clear. But the shop vac is not required. I rarely use one, and I just make sure to lift the bit out of the hole a few times while drilling, just enough to sling out some of the wood chips. This helps to keep the bit from getting clogged which causes heat and dulls the bit.

When sliding the board over, or putting the next board in the jig, you may want to blow the wood chips away off of the jig platform. Otherwise they can create a gap under the board and affect the depth of the pocket hole. The first step with assembly is getting the clamps set up. Because of the 15 degree angle of a pocket screw, it has a tendancy to pull one piece along the other, which leaves a ledge in the joint. To keep this from Pocket Hole Jig Drill Guide Design happening, clamp the pieces in a way that they cannot slip when tightening.

You can see the above picture frame project tutorial here opens in a new window. A good pocket joint requires a tight pocket screw, but not so tight you strip the hole out.

Instead I set my drill to drill no clutch , and I slowly insert the screw until my drill just starts to bog down.

Normally this is when you would pull in the trigger more, but with pocket screws that would be a mistake. Start out by tightening the screw until you can clearly see it pull the gap closed. Snug it up until it feels good and secure, without really driving it in. Doing this is just asking to strip it out. I usually stay about 3 inches from the ends at this point. Remove the screw, cut a couple tooth picks in half, put a small bit of glue in the stripped hole, and then shove in the tooth picks.

Now you can reinsert the screw and it should hold good. Also put some paste wax on the threads of the screw to lubricate them. Just apply some glue, push in the dowel, then saw it off flush. Sand it down to make smooth. There may be some parts of this process that you really just need to get some hands-on experience to fully grasp, but I think you can see that the process is not tough at all.

Drilling pocket holes is messy and this removes the chips very effectively. The jig had three holes spaced apart in such a way that helps you to bore holes whatever distance apart you like. This allows for a lot of flexibility when positioning your holes. Anywhere you place them on the board it fine. Most of the time, you will use the jig to drill pocket holes in the ends of Kreg Pocket Hole Jig Drill Bit Size Guide boards. Make sure the board the screw will be driving into is the face or edge grain board. This is the correct way:.

There is a chart on the back of the screw package to help you decide what length of screw to use. There are fine thread screws for joining hardwoods and coarse thread screws for everything else. I like to keep a stock of these on hand.

The boards need to be clamped together before driving the screws in place. Kreg makes this clamp with wide pads just for this purpose. Set your drill to its slowest speed and drive the screws in until they draw the boards together and stop.

If you drive them in to fast or with too much torque. You might want to set the clutch on your drill to a low number so that it stops twisting when it reaches a certain tightness. For joining boards on their edges, you can hold them together with this right angle clamp. A bar clamp will work too. Again, plan the direction the screws are headed. This is the correct way: the screw goes into the face grain of the board away from the end.

Woodworking Plans Porch Swing Zone Wood Tools Miami