Woodworking Plans Book Stand Out,Bowl And Tray Router Bit With Bearing Error,Massca Jig Hole System Yoga,Wood Turning Pen Blanks 3d - You Shoud Know
With straightforward cuts woodworking plans book stand out a simple assembly, this project comes together in no time. The design boasts hinges for fold-flat storage, woodworking plans book stand out book holder that tilts to a range of viewing angles to accommodate any cook. Difficulty: Easy.
Square cuts and butt joints make the parts of this project fairly easy to assemble. Definitely need to use pockethole screws for this build. Tried with regular wood screws and woodworking plans book stand out split the wood — shoulda known better.
Really nice cookbook stand and a great gift. A nice easy build for a cookbook. By using mortice and tenon joints and making the top a panel rather than just a few boards joined by pocket holes, this could be a simple but elegant lectern for any make shift meeting that requires a place for a speaker.
I'm Jenn. Thanks for stopping by Build Basic. Click on the photo woodworking plans book stand out learn more. Using the cut list above, cut the pieces to size using a miter or hand saw. Using the drawing provided, layout the pieces on a flat work surface.
The specialty parts are the leg, bookrest and slotted stand. Using a miter or handsaw, clip the front corners of the bookrest and bevel one end of the leg woodworking plans book stand out at degrees.
Return the pieces to their place in the front frame. Clamp the straight edge of a scrap block along the first line. Using a handsaw, carve a shallow groove. Repeat to create a grove at each marked line. Return the board to its place in the back frame.
Flip the first board face down, and, using a Kreg Jigbore two pilot holes into the end of the board. Repeat of the opposite end of the board. Once complete, each of these boards should contain four pilot holes.
One-by-one, apply wood glue to the joints, and then clamp them to the work surface. Drive 1 inch wood screws through the pilot holes to secure the parts in place. Apply wood glue to the ends of the slotted stand, and then place the board centered vertically in the frame. Drive wood screws through the pilot holes in the slotted stand to hold it in place in the back frame.
Place the board horizontally inside the frame. Position the board so that its top edge aligns with the marks, and then use wood screws to secure it in place. Using a tape measure, mark the center of the crosspiece installed in the last step. Now drive the screws provided with the hinge into the pilot holes to hold the hinge in place. Position the leg centered woodworking plans book stand out the hinge so that the bevel side is facing downward as shown.
Position the hinge on the leg, drill pilot holes, and secure the hinge in place. Clamp the bookrest woodworking plans book stand out the face of the front frame.
Position the board so that the underside is flush with the bottom edge of the frame. Apply wood glue to the back edge of the bookrest board.
Clamp it in place. Carefully drill pilot holes through the backside of the frame and into the back edge of the bookrest. Using 1 inch wood screws, secure the bookrest in place. Make marks on the backside of the front frame that are 4 inches from each end. Position and secure a hinge inside each mark. Position the hinges of the face of woodworking plans book stand out back frame. Align the sides of the frames, and then secure the hinges to the frame.
Tilt the top edge of the front frame upward, allowing the leg to drop down. Once the beveled end of the leg drops into a slot, it will hold the face frame in place. Leave a Reply Cancel reply Your email address will not be published. Comment Name Email Website.
Mounting Drawer Slides On Bottom Width Rockler Bench Vise University Drawer Glide Brackets Tab Router Table Box Joint Jig Plans 35 |
BELA
16.11.2020 at 14:45:54
BEZPRIDEL
16.11.2020 at 18:33:22
I_S_I
16.11.2020 at 23:11:46
M3ayp
16.11.2020 at 11:56:40
LIL_D_A_D_E
16.11.2020 at 16:49:47