Woodworking Inlay Techniques Violin,Single Stage Dust Collector Canister Filter,Woodcraft Supply Corp 700 - PDF Books
You can decorate a piece of furniture, a wooden box, a guitar neck or a practice block. For your inlay, use any thin, flat material like a wood veneer, a cut of bone, ivory or mother of pearl. One dark and one light 20 Easy Woodworking Techniques Review material is a good idea.
Cut the inlay into a simple shape. You can cut wood veneer using a sharp knife or a machete while a sharp, well-maintained saw will cut mother of pearl. Be sure to dip the pearl in water to prevent burning the material. Stick the piece temporarily on the base. You may use a double-sided tape or glue that takes a long time to set. Sticking the piece on the base will let you trace around it.
Trace the inlay on the wooden base. Use a sharp pencil to trace the outline of the inlay onto the wood. Cut into the traced lines using a sharp knife. You can use an X-Acto knife or another hobby knife; can easily cut into the traced lines.
Begin by lightly scoring the wood to get a groove. Run the knife further down and deeply into the wood. Now you can cut further down with lesser risk of your knife slipping on the surface of the wood.
Cut only into the wood just deep enough to accommodate the inlaid piece. Fit the entire inlaid piece. Set up your cutting tool. A full strength router is the most stable way to cut out a recess for your inlay design.
If one is not available, use a Dremel with a router attachment, or a lighter, less stable router such as a laminate trimmer. Remove the wooden base to the specified depth, but stay away from the outline. That requires a more precise bit. Replace the drill bit with a smaller size and very carefully approach the outline of the recess.
Stop as soon as you reach the groove. When you stop seeing dust and rough, frayed wood appear at the surface, stop immediately. You've reached the groove you created. Glue the piece in. Liberally apply glue to the base of the recess and use a brush to ensure it covers the sides as well. Use a wood glue for veneer. Use an epoxy or other strong, specialized adhesive for a different inlay material. Slightly sanding the edge first will create excess sawdust to mix with the glue and disguise its appearance.
Once the piece is wedged in flush or almost flush with the surface, smooth the glue into the gaps with your finger. Clamp in place and let dry.
Clamp the inlay to something the glue won't adhere to, such as a wooden block covered with tape. Leave it in place for 4—6 hours or for however long your glue takes to set. Level the surface. Remove hardened excess glue and make the inlay flush with the object's surface by using sandpaper, an inlay scraper, or a block plane.
For mother of pearl or abalone , polish additionally with grit sandpaper after flattening the surface with a coarser grit. Cut and place additional pieces. Move on to your next labeled segment and follow the same process to cut out that piece and inlay it. Remember, your previous piece was intentionally large to make a flush, overlapping effect once you've cut into it for the piece above it.
Remember only to make oversized pieces on edges that will be underneath another segment. The other edges should fit your design as precisely as possible. If it's dirty from being stored rather than handled , start by using a damp rag or paper towel.
Avoid anything abrasive. If the dirt goes beyond that, then you would use mild dish soap and water. Don't use chemicals though -- they could damage the art irreparably. Not Helpful 1 Helpful 4. Dave D. By using a router most commonly. This can also be done by using a variety of hand tools. Such as a router plane, chisel, knife, etc.
Anything that can be used to cut and remove potions of wood from the work surface. Not Helpful 0 Helpful 3. Include your email address to get a message when this question is answered. By using this service, some information may be shared with YouTube. Inlaying may be a good finishing touch for a project like making a chess board.
Helpful 0 Not Helpful 1. Alternatively, you can glue all your pieces together first, let them set, then sand or file off the excess glue. The entire inlay can know be placed as though it were one piece. It won't appear as flush as the "overlapping" method described, but it will save a lot of waiting time for projects with many pieces.
Helpful 0 Not Helpful 0. You can buy a wood inlay kit for some routers that allow you to cut the recess, then remove the surrounding "bushing" to cut a perfectly sized inlay. Submit a Tip All tip submissions are carefully reviewed before being published. Dust from sawing or sanding can be dangerous to your lungs, especially when cutting mother of pearl or other shell. Use a respirator dust mask as well as a fan to blow the dust away from your face.
Helpful 6 Not Helpful 4. Wear safety goggles to protect your eyes from small pieces of wood, especially while operating the saw and router. Helpful 4 Not Helpful 2.
Related wikiHows How to. How to. More References 1. Co-authors: Updated: June 2, Categories: Woodworking. Article Summary X To inlay wood, cut the inlay out of a thin piece of wood, and use double sided tape to attach it to the other piece of wood. Bahasa Indonesia: Menatah Kayu. Thanks to all authors Woodworking Inlay Techniques 50 for creating a page that has been read , times. Reader Success Stories Anonymous Sep 3, This did excactly that.
With this help I should be able to do the project with complete success! More reader stories Hide reader stories. Did this article help you? Cookies make wikiHow better. By continuing to use our site, you agree to our cookie policy. About This Article Co-authors: Anonymous Sep 3, Anonymous Dec 30, This helped me understand the right way to inlay birthstones and other things.
File the back of the blade with a metal file to make tight turns easier. Add a zero-clearance table insert to your saw table. This can be as simple as masking tape or a business card taped to the table. Create the stack. Trace the pattern onto the walnut. Attach the aspen to the bottom of the walnut using double-sided tape. Mark the location of the tape to make it easier to separate the stack later.
Use a locking C-clamp to ensure a good tape bond. Set the table angle. Cut counterclockwise and make an oval test cut in the scrap wood outside the pattern lines.
Test the fit of the aspen into the walnut. Adjust the table angle as needed. Drill blade-entry holes. Hide the blade-entry holes by drilling at an angle along straight sections of the lines. The bit enters on the inlay side of the pattern line on the top piece of wood and exits on the waste side of the inlay section on the bottom stock. A slightly steeper angle is better than not enough.
Cut the first inlays. Turn the wood clockwise so the saw blade cuts counterclockwise. As you approach the blade-entry hole to finish the cut, concentrate more on meeting the previous cut than following the line.
Remove the burr from the inlay piece. Remove the pieces through the bottom. Use a flat needle file to remove the burr created when you drilled the blade-entry holes.
|
How To Make A Frame Plant Stand 6g Open Media Vault Hardware 70 Woodworking Down Under Free Plans Me Ball Bearing Drawer Slides Stuck Craft |
yekoglan
23.10.2020 at 11:19:52
AHMET
23.10.2020 at 20:33:22
sevgi_delisi
23.10.2020 at 11:22:13